Bosch Rexroth IndraDrive Mi KCU02 Project Planning Manual Download Page 38

Page: 38 / 422

1.4

About this documentation

1.4.1

Editions

Edition

Release

date

Notes

2012-03 First edition

2014-02 Changes in comparison to previous edition:

●

Changed names of the KSM02 and KMS02 components:
–

KSM02: "motor-integrated servo drive" (previously: "distributed servo drive")

–

KMS02: "near motor servo drive" (previously: "distributed drive controller")

●

Included "Safe Motion" safety option

●

Updated type code

●

Revised E-Stop function

●

Revised sizing of hybrid cable length and control voltage power consumption

●

Included information on locking pins at connectors and connection points of hybrid cables

●

Included conductor colors of hybrid cable for connection points X52, X53 and X54

●

Included internal design of digital inputs/outputs (X37, X38)

24/407

System presentation

IndraDrive Mi Drive Systems with KCU02, KSM02,

KMS02/03, KMV03, KNK03, KLC03

Bosch Rexroth AG R911335703_Edition 04

Summary of Contents for Rexroth IndraDrive Mi KCU02







































































































































































































































































































































































































































Search results

Summary of Contents for Rexroth IndraDrive Mi KCU02

Reviews:

Related manuals for Rexroth IndraDrive Mi KCU02

Brands by name

Popular brands

Bosch Rexroth IndraDrive Mi KCU02, Project Planning Manual

Search results

Summary of Contents for Rexroth IndraDrive Mi KCU02

Reviews:

Related manuals for Rexroth IndraDrive Mi KCU02

Brands by name

Popular brands