Bosch Rexroth IndraDrive Mi KCU02 Project Planning Manual Download Page 173

Page: 173 / 422

6.3.2

X37, X38, digital inputs/outputs

Fig. 6-3:

X37 and X38

View

Connectio

Signal

name

Function

X37.1

ext

External supply 19 … 30 V, max. 1 A, connected to X38.1

X37.2

I/O_3

dig. I/O, configurable

X37.3

0 V

ext

Reference potential; external supply, connected to X38.3

X37.4

I/O_1

dig. I/O, configurable, can be used as probe

X37.5

For cable shield

X38.1

ext

External supply 19 … 30 V, max. 1 A, connected to X37.1

X38.2

I/O_4

dig. I/O, configurable

X38.3

0 V

ext

Reference potential; external supply, connected to X37.3

X38.4

I/O_2

dig. I/O, configurable, can be used as probe

X38.5

For cable shield

M12 (5‑pin, A‑coded) female

Unit

min.

max.

Connection cable, stranded wire

0.25

Cable cross section

AWG

Ready-made connection cable

RKS0010

(optional accessory)

Tab. 6-18:

Function, pin assignment, properties

The digital inputs/outputs comply with IEC 61131-2, type 1.

Properties

●

There is a total of 4 configurable, isolated inputs/outputs which are

distributed over two 5-pin M12 connectors (X37 and X38).
The configuration is carried out with the parameter "P-0-0300, Digital

I/Os, assignment list".

●

The inputs I_1 (X37.4) and I_2 (X38.4) can be used as probe inputs.

IndraDrive Mi Drive Systems with KCU02, KSM02,

KMS02/03, KMV03, KNK03, KLC03

159/407

Connection points

R911335703_Edition 04 Bosch Rexroth AG

Summary of Contents for Rexroth IndraDrive Mi KCU02







































































































































































































































































































































































































































Search results

Summary of Contents for Rexroth IndraDrive Mi KCU02

Reviews:

Related manuals for Rexroth IndraDrive Mi KCU02

Brands by name

Popular brands

Bosch Rexroth IndraDrive Mi KCU02, Project Planning Manual

Search results

Summary of Contents for Rexroth IndraDrive Mi KCU02

Reviews:

Related manuals for Rexroth IndraDrive Mi KCU02

Brands by name

Popular brands