Bosch Rexroth IndraDrive Mi KCU02 Project Planning Manual Download Page 70

Page: 70 / 422

4.3.2

Control cabinet design and cooling

G1 is the only mounting position allowed for supply units and

drive controllers installed in control cabinets.

Possible ways of heat dissipation

Closed control cabinet with

air circulation

Closed control cabinet with

heat exchanger

Control cabinet with fan

Closed control cabinet with

air conditioning unit

~ 400 W

~ 1700 W

~ 2700 W

~ 4000 W

Dissipated heat output

Tab. 4-11:

Possible ways of heat dissipation

The section below describes the "control cabinet with fan".

Requirements for control cabinets

with fan

Risk of damage by unclean air in the control

cabinet!

NOTICE

Operating a control cabinet with a fan, but without the corresponding filters,

can damage the devices or cause malfunction.

●

Install filters at the air intake opening of the control cabinet so that

unclean air cannot get into the control cabinet.

●

Service the filters at regular intervals according to the dust loading in the

environment.

●

Only replace the filters when the fan has been switched off, because

otherwise the fan sucks in the dirt coming off the filter and the dirt gets

into the control cabinet.

56/407

General data and specifications

IndraDrive Mi Drive Systems with KCU02, KSM02,

KMS02/03, KMV03, KNK03, KLC03

Bosch Rexroth AG R911335703_Edition 04

Summary of Contents for Rexroth IndraDrive Mi KCU02







































































































































































































































































































































































































































Search results

Summary of Contents for Rexroth IndraDrive Mi KCU02

Reviews:

Related manuals for Rexroth IndraDrive Mi KCU02

Brands by name

Popular brands

Bosch Rexroth IndraDrive Mi KCU02, Project Planning Manual

Search results

Summary of Contents for Rexroth IndraDrive Mi KCU02

Reviews:

Related manuals for Rexroth IndraDrive Mi KCU02

Brands by name

Popular brands