R5909934 /00
E2 Lite and EC-40
96
Output adjustment panel > Timing Menu
•
Format: Selects the video format of the output
configuration from the drop menu. This is the same
adjustment as in the previous menu.
•
H Total: Adjusts (in pixels) the total pixel count per
line for the selected output.
•
H Front Porch: Adjusts (in pixels) the offset
between the end of the output active area and the
beginning of H sync.
•
H Active: Adjusts (in pixels) the horizontal size of
the output active area.
•
H Sync: Adjusts (in pixels) the H sync width.
•
H Polarity: Adjusts the polarity (active High or Low)
of the horizontal sync pulse (N/A in SDI).
•
V Total: Adjusts (in lines) the total line count per
frame.
•
V Front Porch: Adjusts (in lines) the offset between
the end of the output active area and the beginning
of V sync.
•
V Active: Adjusts (in lines) the vertical size of the
output active area.
•
V Sync: Adjusts (in lines) the V sync width.
•
V Polarity: Adjusts the polarity (active High or Low)
of the vertical sync pulse (N/A in SDI).
•
V Rate: Adjusts the frame rate in seconds polarity
(active High or Low) of the vertical sync pulse (N/A
in SDI).
Note: Changing these values can make the video
signal undetectable for other devices. Always use a
VESA timing calculator for best results.
Output adjustment panel > Connector Menu
Connector Menu: Output Adjustment
—
HDMI
•
Color/Sample/Bit: Adjusts the color space (RGB or
YCbCr), sampling rate (4:4:4 or 4:2:2) and bit
depth (8, 10, or 12) of the output signal.
Depending on the EDID of the connected device
the drop-down list would populate with compatible
settings.
•
Color Range: Adjusts the color range (RGB or
SMPTE, Full or Reduced).
•
Connector Capacity: If the connector is not
assigned to a Destination as above, the capacity
can be changed. Once included in a Destination
configuration this needs to be managed through
the Adjust pane of the Destination.
•
HDCP Mode: HDCP Mode enables the HDCP
setting for the selected output. The default for
HDMI outputs is Off. To turn On the HDCP Mode,
click on the empty checkbox. When the checkbox
displays a check mark, HDCP Mode is On. HDCP
Mode is not applicable to SDI outputs.
Summary of Contents for Event Master E2 Lite
