R5909934 /00
E2 Lite and EC-40
173
Define the Ethernet settings to remotely access is mandatory to control the Event Master series
processor via the Event Master Toolset Software or via a web interface. Please contact the
manager of the local network (LAN) to know how configuring your device.
Query the DHCP server
1.
Select
Ethernet
from the
System
Menu.
The
Ethernet
Menu appears.
2.
Turn On the
DHCP
value.
The Event Master series processor automatically queries the DHCP server for a valid IP address. If the Event
Master series processor receives an IP address, that address is displayed in the Ethernet submenu.
It can take several seconds to obtain an address from the server. During this time, the
SEL
button
remains lit.
Setting a static IP Address
1.
Select
Ethernet
from the
System
Menu.
The
Ethernet
Menu appears.
2.
Turn Off the
DHCP
value.
3.
Select
Set Static IP
from the
Ethernet
Menu.
The
Set Static IP
Menu appears.
4.
Select and set successively the
SUB
(net),
GW
and
IP
fields.
Note:
You must change the
SUB
parameter before editing either of the other parameters.
7.6 Restoring the system
This step in the Event Master series processor setup procedure is optional. If there is not backup
available or if you decide to configure your unit from scratch, please move to the next step to
continue the procedure.
General
In this procedure, you will restore your system configuration from a USB drive
—
provided that you previously
backed up your system to a USB drive.
Prerequisite
•
Ensure that you are familiar with the
USB device (Backup/Restore) Menu
. For details on this menu,
please refer to chapter
System menu > USB device (Backup/Restore)
”
, page 54.
Restore a system configuration file
Use the following steps to restore your system from the USB Drive:
1.
Insert a formatted flash drive in the unit
’
s front-panel USB port.
2.
From the
System
menu, scroll to the
USB Backup/Restore
submenu. Select
Restore
Config.
The
USB Restore Config
submenu appears.
3.
Press
SEL
and scroll through the list of configuration files. When you locate the file you want, press
SEL
again.
A message confirms the restore operation and instructs you to reboot the Event Master series processor.
Summary of Contents for Event Master E2 Lite
