Yamaha YZ 2016 Series Скачать руководство пользователя страница 360 | Manualshive

Страница: 360 / 392

background image

ELECTRICAL COMPONENTS

8-58

FIRST AID IN CASE OF BODILY CONTACT:
EXTERNAL
• Skin — Wash with water.
• Eyes — Flush with water for 15 minutes

and get immediate medical attention.

INTERNAL
• Drink large quantities of water or milk fol-

lowed with milk of magnesia, beaten egg
or vegetable oil. Get immediate medical at-
tention.

ECA

NOTICE

• This is a VRLA (Valve Regulated Lead Ac-

id) battery. Never remove the sealing caps
because the balance between cells will not
be maintained and battery performance
will deteriorate.

• Charging time, charging amperage and

charging voltage for a VRLA (Valve Regu-
lated Lead Acid) battery are different from
those of conventional batteries. The VRLA
(Valve Regulated Lead Acid) battery
should be charged according to the appro-
priate charging method. If the battery is
overcharged, the electrolyte level will drop
considerably. Therefore, take special care
when charging the battery.

TIP

Since VRLA (Valve Regulated Lead Acid) bat-
teries are sealed, it is not possible to check the
charge state of the battery by measuring the
specific gravity of the electrolyte. Therefore, the
charge of the battery has to be checked by
measuring the voltage at the battery terminals.
1. Remove:

• Side cover (left/right)
• Seat

Refer to “GENERAL CHASSIS” on page 4-
1.

2. Disconnect:

• Battery leads

(from the battery terminals)

ECA

NOTICE

First, disconnect the negative battery lead
“1”, and then positive battery lead “2”.

3. Remove:

• Battery

4. Check:

• Battery charge

▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼

a. Connect a pocket tester to the battery termi-

nals.

TIP

• The charge state of a VRLA (Valve Regulated

Lead Acid) battery can be checked by mea-
suring its open-circuit voltage (i.e., the voltage
when the positive battery terminal is discon-
nected).

• No charging is necessary when the open-cir-

cuit voltage equals or exceeds 12.8 V.

b. Check the charge of the battery, as shown in

the charts and the following example.

• Positive tester probe



positive battery terminal

• Negative tester probe



negative battery terminal

Example

Open-circuit voltage = 12.0 V

Charging time = 6.5 hours

Charge of the battery = 20–30%

A. Open-circuit voltage (V)

B. Charging time (hours)

C. Relationship between the open-circuit voltage

and the charging time at 20°C (68°F)

D. These values vary with the temperature, the

condition of the battery plates, and the electro-

lyte level.

1

2

«
...
358
359
360
361
362
...
»

Содержание YZ 2016 Series









































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для YZ 2016 Series

Бренд: Cake Страницы: 13

Бренд: W-Tec Страницы: 6

Бренд: R&G Страницы: 6

Бренд: R&G Страницы: 12

Бренд: BMW Motorrad Страницы: 261

990D0-28K50-CLE

Бренд: Suzuki Страницы: 12

Бренд: Caberg Страницы: 16

Бренд: R&G Страницы: 4

2016 Empulse TT

Бренд: Victory Motorcycles Страницы: 138

Бренд: R&G Страницы: 26

Бренд: MOTO GUZZI Страницы: 266

Бренд: Big Bike Parts Страницы: 3

Бренд: MOTO GUZZI Страницы: 134

Бренд: Serpento Страницы: 66

Бренд: Dakota Digital Страницы: 14

Бренд: Happy Trails Страницы: 2

Бренд: Yamaha Страницы: 80

Бренд: Yamaha Страницы: 63

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды