Yamaha YZ 2016 Series Скачать руководство пользователя страница 117

Страница: 117 / 392

CHASSIS

3-29

EASB296100

CHECKING THE FRONT FORK LEGS

1. Stand the vehicle upright on a level surface.

EWA

WARNING

Securely support the vehicle so that there is
no danger of it falling over.

2. Check:

• Inner tube

Damage/scratches



Replace.

• Front fork leg (s)

Oil leaks between inner tube and outer tube



Replace the oil seal.

3. Hold the vehicle upright and apply the front

brake.

4. Check:

• Front fork operation

Push down hard on the handlebar several
times and check if the front fork rebounds
smoothly.
Unsmooth operation



Correct or replace.

Refer to “FRONT FORK” on page 4-38.

EASB296101

CHECKING THE FRONT FORK PROTEC-
TOR GUIDE

1. Check:

• Protector guide “1”

Out of specification



Replace.

TIP

The protector guide reaches the limit of its use
when it is worn down to the same height “a” as
of the outer tube circumference.

EASB296102

CLEANING THE FRONT FORK OIL SEAL
AND DUST SEAL

1. Remove:

• Protector
• Dust seal “1”

ECA

NOTICE

Be careful not to damage the dust seal and
the inner tube by a driver.

2. Clean:

• Dust seal “a”
• Oil seal “b”

TIP

• Clean the dust seal and oil seal after every

run.

• Apply lithium-soap-based grease on the inner

tube.

EASB296103

AIR BLEEDING FROM FRONT FORK

TIP

If the front fork initial movement feels stiff dur-
ing a run, relieve the front fork internal pres-
sure.
1. Use a suitable stand to raise the front wheel

off the ground.

EWA

WARNING

Securely support the vehicle so that there is
no danger of it falling over.

2. Remove the air bleed screw “1” and release

the internal pressure from the front fork.

Содержание YZ 2016 Series









































































































































































































































































































































































































Результаты поиска

Содержание YZ 2016 Series

Отзывы:

Похожие инструкции для YZ 2016 Series

Бренды по названию

Популярные бренды

Yamaha YZ 2016 Series, Руководство по эксплуатации для владельца

Результаты поиска

Содержание YZ 2016 Series

Отзывы:

Похожие инструкции для YZ 2016 Series

Бренды по названию

Популярные бренды