Yamaha YZ 2016 Series Скачать руководство пользователя страница 289

Страница: 289 / 392

WATER PUMP

6-6

EASB296307

REMOVING THE OIL SEAL

TIP

• Remove the oil seal when the coolant level

changes frequently more than usual, coolant
has discolored, or engine oil has become
milky.

• Do not use the removed oil seal.
1. Remove:

• Oil seals “1”

EASB296308

CHECKING THE WATER PUMP

1. Check:

• Water pump housing cover
• Impeller shaft

Cracks/damage/wear



Replace.

EASB296309

CHECKING THE BEARING

1. Check:

• Bearing

Rotate the inner race with your finger.
Rough spot/seizure



Replace.

EASB296310

INSTALLING THE OIL SEAL

1. Install:

• Oil seals “1”

TIP

• Apply the lithium-soap-based grease on the

oil seal lip.

• Install the oil seal with its manufacture’s

marks or numbers facing the right crankcase
cover “2”.

2. Install:

• Bearing “1”

TIP

Install the bearing by pressing its outer race
parallel.

EASB296311

ASSEMBLING THE WATER PUMP

1. Install:

• Impeller shaft assembly “1”
• Washer “2”
• Pin “3”
• Gear “4”
• Collar “5”
• Circlip “6”

TIP

• Take care so that the oil seal lip is not dam-

aged or the spring does not slip off its posi-
tion.

• Apply the lithium-soap-based grease on the

impeller shaft.

New

5 2

New

Содержание YZ 2016 Series









































































































































































































































































































































































































Результаты поиска

Содержание YZ 2016 Series

Отзывы:

Похожие инструкции для YZ 2016 Series

Бренды по названию

Популярные бренды

Yamaha YZ 2016 Series, Руководство по эксплуатации для владельца

Результаты поиска

Содержание YZ 2016 Series

Отзывы:

Похожие инструкции для YZ 2016 Series

Бренды по названию

Популярные бренды