Yamaha YZ 2016 Series Скачать руководство пользователя страница 359 | Manualshive

Страница: 359 / 392

background image

ELECTRICAL COMPONENTS

8-57

EASB296349

CHECKING THE FUSES

The following procedure applies to all of the
fuses.

ECA

NOTICE

To avoid a short circuit, always stop the en-
gine when checking or replacing a fuse.

1. Remove:

• Side cover (left/right)
• Seat

Refer to “GENERAL CHASSIS” on page 4-
1.

2. Check:

• Main fuse “1”
• Radiator fan motor fuse “2”

▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼

a. Connect the pocket tester to the fuse and

check the continuity.

TIP

Set the pocket tester selector to “

 

1”.

b. If the pocket tester indicates “



”, replace the

fuse.

▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲

3. Replace:

• Fuse

▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼

a. Turn the engine off.
b. Install a new fuse of the correct amperage

rating.

c. Start the engine to verify if the electrical cir-

cuit is operational.

d. If the fuse immediately blows again, check

the electrical circuit.

EWA

WARNING

Never use a fuse with an amperage rating
other than that specified. Improvising or us-
ing a fuse with the wrong amperage rating
may cause extensive damage to the electri-
cal system, cause the lighting and ignition
systems to malfunction and could possibly
cause a fire.

▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲

4. Install:

• Seat
• Side cover (left/right)

Refer to “GENERAL CHASSIS” on page 4-
1.

EASB296350

CHECKING AND CHARGING THE BATTERY

EWA

WARNING

Batteries generate explosive hydrogen gas
and contain electrolyte which is made of
poisonous and highly caustic sulfuric acid.
Therefore, always follow these preventive
measures:
• Wear protective eye gear when handling or

working near batteries.

• Charge batteries in a well-ventilated area.
• Keep batteries away from fire, sparks or

open flames (e.g., welding equipment,
lighted cigarettes).

• DO NOT SMOKE when charging or han-

dling batteries.

• KEEP BATTERIES AND ELECTROLYTE

OUT OF REACH OF CHILDREN.

• Avoid bodily contact with electrolyte as it

can cause severe burns or permanent eye
injury.

Pocket tester

90890-03112

Analog pocket tester

YU-03112-C

1

2

Fuses

Amper-

age rating

Q’ty

Main

15 A

1

Spare

15 A

1

Radiator fan motor

5 A

1

«
...
357
358
359
360
361
...
»

Содержание YZ 2016 Series









































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для YZ 2016 Series

Бренд: DAELIM Страницы: 2

SPORTCITY CUBE 125

Бренд: APRILIA Страницы: 157

MILWAUKEE-EIGHT 5833

Бренд: JIMS Страницы: 10

Бренд: Nuviz Страницы: 46

Бренд: GYS Страницы: 36

Бренд: Miller Страницы: 22

Бренд: Yamaha Страницы: 112

Бренд: hepco & becker Страницы: 3

H-NAPE CHINSTRAP

Бренд: Fast Страницы: 24

Бренд: Tipperary Страницы: 2

Бренд: CRATONI Страницы: 44

Бренд: Palm Страницы: 14

VarioProtect PANORAMA-W R-TC

Бренд: Schweißkraft Страницы: 22

Kawasaki NINJA 650

Бренд: Arrow Страницы: 7

Бренд: Brixton Страницы: 148

Бренд: Oxford Страницы: 40

HotGrips OF690 Adventure

Бренд: Oxford Страницы: 42

Бренд: Christini Страницы: 92

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды