Yamaha YZ 2016 Series Скачать руководство пользователя страница 181

Страница: 181 / 392

STEERING HEAD

4-53

2. Install:

• Bearing races
• Upper bearing “1”
• Bearing race cover “2”

TIP

Apply the lithium-soap-based grease on the
bearing and bearing race cover lip.

3. Install:

• Lower bracket “1”

TIP

Apply the lithium-soap-based grease on the
bearing, the portion “a” and thread of the steer-
ing stem.

4. Install:

• Steering ring nut “1”

TIP

Install the steering nut with its stepped side “a”
facing downward.

Tighten the steering ring nut with a steering
nut wrench “2”.
Refer to “CHECKING AND ADJUSTING
THE STEERING HEAD” on page 3-34.

5. Check the steering stem by turning this lock

to lock. If there is any binding, remove the
steering stem and check the steering bear-
ing.

6. Install:

• Washer “1”

7. Install:

• Front fork “1”
• Upper bracket “2”

TIP

• Temporarily tighten the pinch bolts (lower

bracket).

• Do not tighten the pinch bolts (upper bracket)

yet.

Steering ring nut

7 Nm (0.7 m·kgf, 5.1 ft·lbf)

Содержание YZ 2016 Series









































































































































































































































































































































































































Результаты поиска

Содержание YZ 2016 Series

Отзывы:

Похожие инструкции для YZ 2016 Series

Бренды по названию

Популярные бренды

Yamaha YZ 2016 Series, Руководство по эксплуатации для владельца

Результаты поиска

Содержание YZ 2016 Series

Отзывы:

Похожие инструкции для YZ 2016 Series

Бренды по названию

Популярные бренды