Yamaha YZ 2016 Series Скачать руководство пользователя страница 103

Страница: 103 / 392

ENGINE

3-15

4. If the oil filter element is also to be replaced,

perform the following procedure.

▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼

a. Remove the oil filter element cover “1” and

oil filter element “2”.

b. Replace the O-ring “3”.

c. Install the new oil filter element and the oil fil-

ter element cover.

▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲

5. To check the oil strainer, perform the follow-

ing procedure.

▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼

a. Remove the oil strainer “1”.
b. Check the oil strainer.

Damage



Replace.

Clogging due to dirt



Wash with kerosene.

c. Replace the O-ring “2”.

d. Install the oil strainer.

▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲

6. Install:

• Gasket
• Drain bolt

7. Pour the specified amount of engine oil into

the oil filler cap hole.

8. Install:

• Oil filler cap

9. Check:

• Oil level

Refer to “CHECKING THE ENGINE OIL
LEVEL” on page 3-14.

Oil filter element cover bolt

10 Nm (1.0 m·kgf, 7.2 ft·lbf)

New

Oil strainer bolt

10 Nm (1.0 m·kgf, 7.2 ft·lbf)

Drain bolt

20 Nm (2.0 m·kgf, 14 ft·lbf)

Engine oil quantity

Oil change

0.83 L (0.88 US qt, 0.73 Imp.qt)

With oil filter removal

0.85 L (0.90 US qt, 0.75 Imp.qt)

Quantity (disassembled)

1.10 L (1.16 US qt, 0.97 Imp.qt)

New

Содержание YZ 2016 Series









































































































































































































































































































































































































Результаты поиска

Содержание YZ 2016 Series

Отзывы:

Похожие инструкции для YZ 2016 Series

Бренды по названию

Популярные бренды

Yamaha YZ 2016 Series, Руководство по эксплуатации для владельца

Результаты поиска

Содержание YZ 2016 Series

Отзывы:

Похожие инструкции для YZ 2016 Series

Бренды по названию

Популярные бренды