Yamaha YZ 2016 Series Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 392

background image

EASB296005

SAFETY INFORMATION

THIS MACHINE IS DESIGNED STRICTLY FOR COMPETITION USE, ONLY ON A CLOSED
COURSE. It is illegal for this machine to be operated on any public street, road, or highway. Off-road
use on public lands may also be illegal. Please check local regulations before riding.
• THIS MACHINE IS TO BE OPERATED BY AN EXPERIENCED RIDER ONLY.Do not attempt to

operate this machine at maximum power until you are totally familiar with its characteristics.

• THIS MACHINE IS DESIGNED TO BE RIDDEN BY THE OPERATOR ONLY.Do not carry passen-

gers on this machine.

• ALWAYS WEAR PROTECTIVE APPAREL.When operating this machine, always wear an ap-

proved helmet with goggles or a face shield. Also wear heavy boots, gloves, and protective clothing.
Always wear proper fitting clothing that will not be caught in any of the moving parts or controls of
the machine.

• ALWAYS MAINTAIN YOUR MACHINE IN PROPER WORKING ORDER.For safety and reliability,

the machine must be properly maintained. Always perform the pre-operation checks indicated in
this manual.Correcting a mechanical problem before you ride may prevent an accident.

• GASOLINE IS HIGHLY FLAMMABLE.Always turn off the engine while refueling. Take care to not

spill any gasoline on the engine or exhaust system. Never refuel in the vicinity of an open flame, or
while smoking.

• GASOLINE CAN CAUSE INJURY.If you should swallow some gasoline, inhale excess gasoline va-

pors, or allow any gasoline to get into your eyes, contact a doctor immediately. If any gasoline spills
onto your skin or clothing, immediately wash skin areas with soap and water, and change your
clothes.

• ONLY OPERATE THE MACHINE IN AN AREA WITH ADEQUATE VENTILATION.Never start the

engine or let it run for any length of time in an enclosed area. Exhaust fumes are poisonous. These
fumes contain carbon monoxide, which by itself is odorless and colorless. Carbon monoxide is a
dangerous gas which can cause unconsciousness or can be lethal.

• PARK THE MACHINE CAREFULLY; TURN OFF THE ENGINE.Always turn off the engine if you

are going to leave the machine. Do not park the machine on a slope or soft ground as it may fall
over.

• THE ENGINE, EXHAUST PIPE AND MUFFLER WILL BE VERY HOT AFTER THE ENGINE HAS

BEEN RUN.Be careful not to touch them or to allow any clothing item to contact them during inspec-
tion or repair.

• PROPERLY SECURE THE MACHINE BEFORE TRANSPORTING IT.For safety, drain the gaso-

line from the fuel tank before transporting the vehicle.

«
...
3
4
5
6
7
...
»

Содержание YZ 2016 Series









































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для YZ 2016 Series

Бренд: R&G Страницы: 12

Бренд: KTM Страницы: 163

Бренд: PEUGEOT Страницы: 12

Бренд: NEO TOOLS Страницы: 8

Бренд: Yamaha Страницы: 104

Super Tenere ABS 2018

Бренд: Yamaha Страницы: 122

Бренд: Yamaha Страницы: 124

Бренд: Yamaha Страницы: 97

Бренд: DYNATEK Страницы: 11

Бренд: DYNATEK Страницы: 12

Бренд: Shift Power Страницы: 7

Бренд: Shark Страницы: 8

VarioProtect PANORAMA-W R-TC

Бренд: Schweißkraft Страницы: 22

CIAK MASTER 50-4T

Бренд: Malaguti Страницы: 31

MARATHON 125 AC

Бренд: RIEJU Страницы: 40

Бренд: Yadea Страницы: 66

RST MILLE FUTURA - PART 1 2000

Бренд: APRILIA Страницы: 58

Бренд: KTM Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды