Yamaha YZ 2016 Series Скачать руководство пользователя страница 106

Страница: 106 / 392

ENGINE

3-18

c. Measure the valve clearance “e” using a

thickness gauge “1”.

TIP

Record the measured reading if the clearance
is incorrect.

▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲

5. Adjust:

• Valve clearance

▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼

a. Remove the camshaft (intake and exhaust).

Refer to “CAMSHAFT” on page 5-12.

b. Remove the valve lifter “2” and the adjusting

pad “3” with a valve lapper “1”.

TIP

• Place a cloth in the timing chain space to pre-

vent adjusting pads from falling into the crank-
case.

• Identity each valve lifter and adjusting pad po-

sition very carefully so that they can be rein-
stalled in their original place.

c. Check the number on the originally installed

adjusting pad.

TIP

• The adjusting pad number “a” is indicated on

the top of the adjusting pad.

• For the number on the originally installed ad-

justing pad, convert the last digit of adjusting
pad number as per the below table.

Valve lapper

90890-04101

Valve lapping tool

YM-A8998

Содержание YZ 2016 Series









































































































































































































































































































































































































Результаты поиска

Содержание YZ 2016 Series

Отзывы:

Похожие инструкции для YZ 2016 Series

Бренды по названию

Популярные бренды

Yamaha YZ 2016 Series, Руководство по эксплуатации для владельца

Результаты поиска

Содержание YZ 2016 Series

Отзывы:

Похожие инструкции для YZ 2016 Series

Бренды по названию

Популярные бренды