Yamaha YZ 2016 Series Скачать руководство пользователя страница 96

Страница: 96 / 392

ENGINE

3-8

EASB296071

ENGINE

EASB296072

CHECKING THE COOLANT LEVEL

EWA

WARNING

If coolant seems hot, do not remove the ra-
diator cap.

1. Stand the vehicle upright on a level surface.
2. Remove:

• Radiator cap “1”

3. Check:

• Coolant level

Maximum level “a” or below



Add coolant

up to the maximum level.

ECA

NOTICE

• Adding water instead of coolant lowers the

antifreeze content. If, therefore, water is
used instead of coolant, check, and if nec-
essary, adjust the antifreeze concentra-
tion.

• Use only distilled water. However, if dis-

tilled water is not available, soft water may
be used.

4. Start the engine, warm this up for 3 minutes,

and then stop it.

5. Check:

• Coolant level

TIP

Before checking the coolant level, wait a few
minutes until the coolant has settled.

EASB296073

CHECKING THE COOLING SYSTEM

1. Remove:

• Seat
• Side cover (left/right)
• Air scoop (left/right)

Refer to “GENERAL CHASSIS” on page 4-
1.

• Air filter case cover

Refer to “THROTTLE BODY” on page 7-5.

2. Check:

• Radiator
• Radiator hoses

Crack/damage



Replace.

Refer to “RADIATOR” on page 6-1.

3. Install:

• Air filter case cover

Refer to “THROTTLE BODY” on page 7-5.

• Air scoop (left/right)
• Seat
• Side cover (left/right)

Refer to “GENERAL CHASSIS” on page 4-
1.

EASB296074

CHANGING THE COOLANT

EWA

WARNING

If coolant seems hot, do not remove the ra-
diator cap.

1. Place a container under the engine.
2. Remove:

• Coolant drain bolt “1”

3. Remove:

• Radiator cap

Slowly loosen the radiator cap to drain cool-
ant.

TIP

When the radiator cap is loosened, coolant will
gush out transversely; therefore, bring the con-
tainer near to the outlet.
4. Thoroughly flush the cooling system with

clean tap water.

1. Radiator

Содержание YZ 2016 Series









































































































































































































































































































































































































Результаты поиска

Содержание YZ 2016 Series

Отзывы:

Похожие инструкции для YZ 2016 Series

Бренды по названию

Популярные бренды

Yamaha YZ 2016 Series, Руководство по эксплуатации для владельца

Результаты поиска

Содержание YZ 2016 Series

Отзывы:

Похожие инструкции для YZ 2016 Series

Бренды по названию

Популярные бренды