Yamaha YZ 2016 Series Скачать руководство пользователя страница 361 | Manualshive

Страница: 361 / 392

background image

ELECTRICAL COMPONENTS

8-59

▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲

5. Charge:

• Battery

(refer to the appropriate charging method)

EWA

WARNING

Do not quick charge a battery.

ECA

NOTICE

• Do not use a high-rate battery charger

since it forces a high-amperage current
into the battery quickly and can cause bat-
tery overheating and battery plate dam-
age.

• If it is impossible to regulate the charging

current on the battery charger, be careful
not to overcharge the battery.

• When charging a battery, be sure to re-

move it from the vehicle. (If charging has
to be done with the battery mounted on the
vehicle, disconnect the negative battery
lead from the battery terminal.)

• To reduce the chance of sparks, do not

plug in the battery charger until the battery
charger leads are connected to the bat-
tery.

• Before removing the battery charger lead

clips from the battery terminals, be sure to
turn off the battery charger.

• Make sure the battery charger lead clips

are in full contact with the battery terminal
and that they are not shorted. A corroded
battery charger lead clip may generate
heat in the contact area and a weak clip
spring may cause sparks.

• If the battery becomes hot to the touch at

any time during the charging process, dis-
connect the battery charger and let the
battery cool before reconnecting it. Hot
batteries can explode!

• As shown in the following illustration, the

open-circuit voltage of a VRLA (Valve Reg-
ulated Lead Acid) battery stabilizes about
30 minutes after charging has been com-
pleted. Therefore, wait 30 minutes after
charging is completed before measuring
the open-circuit voltage.

▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼

Charging method using a variable-cur-
rent (voltage) charger

a. Measure the open-circuit voltage prior to

charging.

TIP

Voltage should be measured 30 minutes after
the engine is stopped.
b. Connect a charger and ammeter to the bat-

tery and start charging.

TIP

Set the charging voltage to 16–17 V. If the set-
ting is lower, charging will be insufficient. If too
high, the battery will be over-charged.
c. Make sure that the current is higher than the

standard charging current written on the bat-
tery.

TIP

If the current is lower than the standard charg-
ing current written on the battery, set the charg-
ing voltage adjust dial at 20–24 V and monitor
the amperage for 3–5 minutes to check the bat-
tery.

A. Open-circuit voltage (V)

B. Charging condition of the battery (%)

C. Ambient temperature 20°C (68°F)

A. Open-circuit voltage (V)

B. Time (minutes)

C. Charging

D. Ambient temperature 20°C (68°F)

E. Check the open-circuit voltage.

• Standard charging current is reached

Battery is good.

• Standard charging current is not reached

Replace the battery.

«
...
359
360
361
362
363
...
»

Содержание YZ 2016 Series









































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для YZ 2016 Series

Бренд: B-PWR Страницы: 12

Бренд: GAS GAS Страницы: 34

Бренд: VIKING BAGS Страницы: 2

Stealth Air Cleaner Kit

Бренд: S&S Cycle Страницы: 4

Бренд: Ducati Страницы: 77

Бренд: CRATONI Страницы: 61

Бренд: ESAB Страницы: 4

Бренд: X&I Страницы: 59

Бренд: Arai Страницы: 2

Krauser 610.092 00 02

Бренд: Wunderlich Страницы: 4

TERMOSCUD R224X

Бренд: tucanourbano Страницы: 4

Бренд: Cagiva Страницы: 136

Бренд: Cagiva Страницы: 162

Бренд: X-lite Страницы: 57

Бренд: Yamaha Страницы: 3

Бренд: Yamaha Страницы: 94

Бренд: Yamaha Страницы: 23

Бренд: Yamaha Страницы: 46

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды