Yamaha YZ 2016 Series Скачать руководство пользователя страница 100

Страница: 100 / 392

ENGINE

3-12

2. Lubricate:

• Throttle cable end “a”

3. Install:

• Throttle grip cap
• Screw (throttle grip cap)

4. Install:

• Cover (grip cap)
• Cover (throttle cable cap)

EWA

WARNING

Check that the throttle grip moves smooth-
ly. If this does not move smoothly, correct
the installed positions.

EASB296081

CLEANING THE AIR FILTER ELEMENT

1. Remove:

• Fuel tank cap cover “1”

Refer to “FUEL TANK CAP” on page 1-18.

• Air filter case cover “2”

TIP

Loosen the quick fastener screw “3” and re-
move the air filter case cover.

2. Remove:

• Air filter mounting bolt “1”
• Air filter element “2”
• Air filter guide “3” (from the air filter element)

3. Wash:

• Air filter element

EWA

WARNING

Do not use gasoline or organic (acid/alka-
line) volatile oil for washing.

TIP

After washing the element with air filter cleaner
or kerosene, squeeze and dry it completely.

ECA

NOTICE

Do not twist the element when squeezing
the element.

4. Check:

• Air filter element

Damage



Replace.

5. Foam-air-filter oil or equivalent oil to the ele-

ment

TIP

Squeeze out the excess oil. Element should be
wet but not dripping.
6. Install:

• Air filter guide “1” (to the air filter element)
• Air filter element “2”
• Air filter mounting bolt “3”

Recommended lubricant

Lithium-soap-based grease

Screw (throttle grip cap)

3.8 Nm (0.38 m·kgf, 2.8 ft·lbf)

Oil application quantify

50 g

Air filter mounting bolt

2.0 Nm (0.20 m·kgf, 1.4 ft·lbf)

Содержание YZ 2016 Series









































































































































































































































































































































































































Результаты поиска

Содержание YZ 2016 Series

Отзывы:

Похожие инструкции для YZ 2016 Series

Бренды по названию

Популярные бренды

Yamaha YZ 2016 Series, Руководство по эксплуатации для владельца

Результаты поиска

Содержание YZ 2016 Series

Отзывы:

Похожие инструкции для YZ 2016 Series

Бренды по названию

Популярные бренды