Yamaha YZ 2016 Series Скачать руководство пользователя страница 180

Страница: 180 / 392

STEERING HEAD

4-52

EASB296178

REMOVING THE LOWER BRACKET

1. Use a suitable stand to raise the front wheel

off the ground.

EWA

WARNING

Securely support the vehicle so that there is
no danger of it falling over.

2. Remove:

• Rng nut “1”

TIP

Remove the ring nut with the steering nut
wrench “2”.

EWA

WARNING

Securely support the lower bracket so that
there is no danger of it falling.

EASB296179

CHECKING THE STEERING HEAD

1. Wash with kerosene:

• Bearing
• Bearing races

2. Check:

• Bearing
• Bearing races

Damage/pitting



Replace.

3. Replace:

• Bearing
• Bearing races

▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼

a. Remove the bearing race from the steering

head pipe with a long rod “1” and a hammer.

b. Remove the bearing race from the lower

bracket with a chisel “2” and a hammer.

c. Install a new bearing race.

ECA

NOTICE

If the bearing race is not installed properly,
the steering head pipe could be damaged.

TIP

Always replace the bearing and the bearing
race as a set.

▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲

4. Check:

• Upper bracket
• Lower bracket

(along with the steering stem)
Bends/cracks/damage



Replace.

EASB296180

INSTALLING THE STEERING HEAD

1. Install:

• Lower bearing “1”

TIP

Apply the lithium-soap-based grease on the
dust seal lip and bearing inner circumference.

Steering nut wrench

90890-01403

Exhaust flange nut wrench

YU-A9472

Содержание YZ 2016 Series









































































































































































































































































































































































































Результаты поиска

Содержание YZ 2016 Series

Отзывы:

Похожие инструкции для YZ 2016 Series

Бренды по названию

Популярные бренды

Yamaha YZ 2016 Series, Руководство по эксплуатации для владельца

Результаты поиска

Содержание YZ 2016 Series

Отзывы:

Похожие инструкции для YZ 2016 Series

Бренды по названию

Популярные бренды