Yamaha YZ 2016 Series Скачать руководство пользователя страница 136

Страница: 136 / 392

REAR WHEEL

4-8

EASB296135

REMOVING THE REAR WHEEL

1. Use a suitable stand to raise the rear wheel

off the ground.

EWA

WARNING

Securely support the vehicle so that there is
no danger of it falling over.

2. Remove:

• Rear wheel axle nut “1”

3. Loosen:

• Locknut “2”

4. Tighten:

• Adjusting bolt “3”

5. Remove:

• Rear wheel axle
• Rear wheel

TIP

• Push the rear wheel forward and remove the

drive chain from the rear wheel sprocket.

• Do not depress the brake pedal with the rear

wheel removed.

EASB296136

CHECKING THE REAR WHEEL

1. Check:

• Rear wheel axle
• Rear wheel
• Bearing
• Oil seals

Refer to “CHECKING THE FRONT WHEEL”
on page 4-4.

2. Check:

• Tire(s)
• Rear wheel

Damage/wear



Replace.

Refer to “CHECKING THE TIRES” on page
3-33 and “CHECKING THE WHEELS” on
page 3-34.

3. Check:

• Spokes

Refer to “CHECKING THE FRONT WHEEL”
on page 4-4.

4. Measure:

• Radial wheel runout
• Lateral wheel runout

Refer to “CHECKING THE FRONT WHEEL”
on page 4-4.

EASB296137

DISASSEMBLING THE REAR WHEEL

1. Remove:

• Oil seals
• Bearing

Refer to “DISASSEMBLING THE FRONT
WHEEL” on page 4-5.

EASB296138

CHECKING AND REPLACING THE REAR
WHEEL SPROCKET

1. Check:

• Rear wheel sprocket

More than 1/4 tooth wear “a”



Replace the

rear wheel sprocket and the drive sprocket
as a set.
Bent tooth



Replace the rear wheel

sprocket and the drive sprocket as a set.

2. Replace:

• Rear wheel sprocket

▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼

a. Remove the self-locking nuts and the rear

wheel sprocket.

b. Clean the rear wheel drive hub with a clean

cloth, especially the surfaces that contact
the sprocket.

c. Install the new rear wheel sprocket.

Radial wheel runout limit

2.0 mm (0.08 in)

Lateral wheel runout limit

2.0 mm (0.08 in)

b. Correct

1. Drive chain roller

2. Rear wheel sprocket

Rear wheel sprocket self-locking

nut

50 Nm (5.0 m·kgf, 36 ft·lbf)

Содержание YZ 2016 Series









































































































































































































































































































































































































Результаты поиска

Содержание YZ 2016 Series

Отзывы:

Похожие инструкции для YZ 2016 Series

Бренды по названию

Популярные бренды

Yamaha YZ 2016 Series, Руководство по эксплуатации для владельца

Результаты поиска

Содержание YZ 2016 Series

Отзывы:

Похожие инструкции для YZ 2016 Series

Бренды по названию

Популярные бренды