Yamaha YZ 2016 Series Скачать руководство пользователя страница 194 | Manualshive

Страница: 194 / 392

background image

CHAIN DRIVE

4-66

EAS23420

REMOVING THE DRIVE CHAIN

1. Stand the vehicle on a level surface.

EWA

WARNING

Securely support the vehicle so that there is
no danger of it falling over.

TIP

Place the vehicle on a suitable stand so that the
rear wheel is elevated.
2. Remove:

• Drive chain

TIP

Cut the drive chain with the drive chain cut &
rivet tool. (Use goods on the market)

EAS23441

CHECKING THE DRIVE CHAIN

1. Measure:

• 15-link section of the drive chain

Out of specification



Replace the drive

chain.

▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼

a. Measure the length “a” between the inner

sides of the pins and the length “b” between
the outer sides of the pins on a 15-link sec-
tion of the drive chain as shown in the illus-
tration.

b. Calculate the length “c” of the 15-link section

of the drive chain using the following formu-
la.
Drive chain 15-link section length “c” =
(length “a” between pin inner sides + length
“b” between pin outer sides)/2

TIP

• When measuring a 15-link section of the drive

chain, make sure that the drive chain is taut.

• Perform this procedure 2–3 times, at a differ-

ent location each time.

▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲

2. Check:

• Drive chain

Stiffness



Clean, lubricate, or replace.

3. Clean:

• Drive chain

▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼

a. Wipe the drive chain with a clean cloth.
b. Put the drive chain in kerosene and remove

any remaining dirt.

c. Remove the drive chain from the kerosene

and completely dry it.

ECA

NOTICE

• This vehicle has a drive chain with small

rubber O-rings “1” between the drive
chain side plates. Never use high-pressure
water or air, steam, gasoline, certain sol-
vents (e.g., benzine), or a coarse brush to
clean the drive chain. High-pressure meth-
ods could force dirt or water into the drive
chain’s internals, and solvents will deteri-
orate the O-rings. A coarse brush can also
damage the O-rings. Therefore, use only
kerosene to clean the drive chain.

• Do not soak the drive chain in kerosene for

more than ten minutes, otherwise the O-
rings can be damaged.

15-link length limit

239.3 mm (9.42 in)

«
...
192
193
194
195
196
...
»

Содержание YZ 2016 Series









































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для YZ 2016 Series

Бренд: Palm Страницы: 14

Бренд: N-Com Страницы: 36

Бренд: VEB Страницы: 63

Бренд: Shark Страницы: 52

Бренд: Miller Страницы: 12

Бренд: Sachs Bikes Страницы: 84

Бренд: Bajaj Страницы: 39

Бренд: Yamaha Страницы: 86

Бренд: Yamaha Страницы: 88

TDM850'99 4TX-AE3

Бренд: Yamaha Страницы: 43

Бренд: Yamaha Страницы: 118

Бренд: Yamaha Страницы: 92

Бренд: Yamaha Страницы: 105

Бренд: Yamaha Страницы: 111

Бренд: Yamaha Страницы: 88

Бренд: Yamaha Страницы: 94

STRATOLINER XV19CTSC

Бренд: Yamaha Страницы: 100

Бренд: Yamaha Страницы: 98

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды