Yamaha YZ 2016 Series Скачать руководство пользователя страница 119 | Manualshive

Страница: 119 / 392

background image

CHASSIS

3-31

EASB296105

CHECKING THE SWINGARM OPERATION

1. Check:

• Swingarm smooth action
• Swingarm free play

Refer to “SWINGARM” on page 4-62.

EASB296106

CHECKING THE REAR SUSPENSION

1. Stand the vehicle upright on a level surface.

EWA

WARNING

Securely support the vehicle so that there is
no danger of it falling over.

2. Check:

• Rear shock absorber assembly

Gas leaks/oil leaks



Replace the rear

shock absorber assembly.
Refer to “REAR SHOCK ABSORBER AS-
SEMBLY” on page 4-55.

3. Check:

• Rear shock absorber assembly smooth ac-

tion

• Rear suspension link smooth action

Sit astride the seat and shake your body up
and down several times to check whether
the rear shock absorber assembly operates
smoothly.
Unsmooth operation



Correct or replace.

Refer to “REAR SHOCK ABSORBER AS-
SEMBLY” on page 4-55.

EASB296107

ADJUSTING THE REAR SHOCK ABSORB-
ER ASSEMBLY

Use a suitable stand to raise the rear wheel off
the ground.

EWA

WARNING

Securely support the vehicle so that there is
no danger of it falling over.

Spring preload

ECA

NOTICE

Do not turn the adjuster forcibly beyond its
adjusting range.

1. Remove:

• Rear frame

Refer to “REAR SHOCK ABSORBER AS-
SEMBLY” on page 4-55.

2. Adjust:

• Spring preload

▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼

a. Loosen the locknut “1”.
b. Loosen the adjuster “2” until there is some

clearance between the spring and the ad-
juster.

c. Measure the spring free length “a”.

d. Turn the adjuster in the direction of “b” or “c”

to make an adjustment.

TIP

• Be sure to remove all dirt and mud from

around the locknut and adjusting ring before
adjustment.

• The length of the spring (installed) changes

1.5 mm (0.06 in) per turn of the adjusting ring.

Direction “b”

Spring preload is increased (suspen-

sion is harder).

Direction “c”

Spring preload is decreased (suspen-

sion is softer).

Spring preload adjusting positions

Minimum

Position in which the spring is

turned in 1.5 mm (0.06 in) from

its free length.

Standard

Position in which the spring is

turned in 10 mm (0.39 in) from its

free length.

Maximum

Position in which the spring is

turned in 18 mm (0.71 in) from its

free length.

«
...
117
118
119
120
121
...
»

Содержание YZ 2016 Series









































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для YZ 2016 Series

Бренд: Yamaha Страницы: 94

Бренд: Yamaha Страницы: 44

Бренд: Honda Страницы: 118

Бренд: Yamaha Страницы: 568

Бренд: Parweld Страницы: 4

Бренд: Honda Страницы: 26

Бренд: Salewa Страницы: 17

Бренд: EINHELL Страницы: 48

Бренд: KTM Power Parts Страницы: 12

Бренд: Kinderkraft Страницы: 36

Бренд: R&G Страницы: 6

Бренд: R&G Страницы: 9

Бренд: R&G Страницы: 11

Бренд: Cagiva Страницы: 157

2003 Planet 125

Бренд: Cagiva Страницы: 156

2007 raptor 125-E 3

Бренд: Cagiva Страницы: 156

Бренд: Yamaha Страницы: 32

Бренд: Yamaha Страницы: 98

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды