Yamaha YZ 2016 Series Скачать руководство пользователя страница 133

Страница: 133 / 392

FRONT WHEEL

4-5

EASB296131

DISASSEMBLING THE FRONT WHEEL

1. Remove:

• Oil seals
• Bearings

▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼

a. Clean the outside of the front wheel hub.
b. Remove the oil seals “1” with a flat-head

screwdriver.

TIP

To prevent damaging the wheel, place a rag “2”
between the screwdriver and the wheel sur-
face.

c. Remove the bearings with a bearing puller.

▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲

EASB296132

ASSEMBLING THE FRONT WHEEL

1. Install:

• Bearing (left side) “1”
• Spacer “2”
• Bearing (right side) “3”
• Oil seals “4”

TIP

• Apply the lithium-soap-based grease to the

bearing and the oil seal lip when installing.

• Left side of bearing shall be installed first.
• Install the oil seal with its manufacture’s

marks or numbers facing outward.

ECA

NOTICE

Install the bearing by pressing its outer race
parallel.

TIP

Use a socket “1” that matches the diameter of
the bearing outer race and that of the oil seal.

2. Install:

• Brake disc “1”
• Brake disc bolt “2”

TIP

Tighten the bolts in stages and in a crisscross
pattern.

New

Brake disc bolt

12 Nm (1.2 m·kgf, 8.7 ft·lbf)

LOCTITE®

New

Содержание YZ 2016 Series









































































































































































































































































































































































































Результаты поиска

Содержание YZ 2016 Series

Отзывы:

Похожие инструкции для YZ 2016 Series

Бренды по названию

Популярные бренды

Yamaha YZ 2016 Series, Руководство по эксплуатации для владельца

Результаты поиска

Содержание YZ 2016 Series

Отзывы:

Похожие инструкции для YZ 2016 Series

Бренды по названию

Популярные бренды