Yamaha YZ 2016 Series Скачать руководство пользователя страница 261

Страница: 261 / 392

OIL PUMP AND BALANCER GEAR

5-62

EASB296278

INSTALLING THE OIL PUMP AND BALANC-
ER GEAR

1. Install:

• Oil pump assembly “1”
• Oil pump assembly bolt “2”

ECA

NOTICE

After tightening the bolts, make sure that
the oil pump turns smoothly.

2. Install:

• Collar “1”
• Balancer weight gear “2”

TIP

Install the balancer weight gear and balancer
shaft with their lower splines “a” aligning with
each other.

3. Install:

• Balancer drive gear “1”
• Collar “2”

TIP

• Align the punched mark “a” on the balancer

drive gear with the punched mark “b” on the
balancer weight gear.

• Install the balancer drive gear and crankshaft

with the lower splines “c” aligning with each
other.

4. Install:

• Conical washer “1”
• Balancer weight gear nut “2”

• Primary drive gear “3”
• Conical washer “4”
• Primary drive gear nut “5”

• Balancer “6”
• Conical washer “7”
• Balancer nut “8”

TIP

• Apply engine oil to the contact surface and

threaded portion of the primary drive gear nut.

• Place an aluminum plate “a” between the

teeth of the balancer drive gear “9” and bal-
ancer weight gear “10”.

• Install the conical washer with its convex sur-

face “b” outward.

• Align the balancer flat portion “c” with the flat

portion “d”.

• Apply the engine oil to the contact surface and

threaded portion of the balancer nut.

Oil pump assembly bolt

5 Nm (0.5 m·kgf, 3.6 ft·lbf)

LOCTITE®

Balancer weight gear nut

50 Nm (5.0 m·kgf, 36 ft·lbf)

Primary drive gear nut

75 Nm (7.5 m·kgf, 54 ft·lbf)

Balancer nut

38 Nm (3.8 m·kgf, 27 ft·lbf)

New

Содержание YZ 2016 Series









































































































































































































































































































































































































Результаты поиска

Содержание YZ 2016 Series

Отзывы:

Похожие инструкции для YZ 2016 Series

Бренды по названию

Популярные бренды

Yamaha YZ 2016 Series, Руководство по эксплуатации для владельца

Результаты поиска

Содержание YZ 2016 Series

Отзывы:

Похожие инструкции для YZ 2016 Series

Бренды по названию

Популярные бренды