Yamaha YZ 2016 Series Скачать руководство пользователя страница 97 | Manualshive

Страница: 97 / 392

background image

ENGINE

3-9

5. Install:

• Copper washer
• Coolant drain bolt

6. Pour coolant.

EWA

WARNING

• If coolant splashes in your eyes, thorough-

ly wash them with water and consult a
doctor.

• If coolant splashes on your clothes, quick-

ly wash it away with water and then with
soap and water.

• If coolant is swallowed, induce vomiting

and get immediate medical attention.

ECA

NOTICE

• Adding water instead of coolant lowers the

antifreeze content of the coolant. If water
is used instead of coolant check, and if
necessary, correct the antifreeze concen-
tration of the coolant.

• Use only distilled water. However, if dis-

tilled water is not available, soft water may
be used.

• If coolant comes into contact with painted

surfaces, immediately wash them with wa-
ter.

• Do not mix different types of antifreeze.

7. Install:

• Radiator cap

8. Start the engine, warm this up for 3 minutes,

stop it, and then wait for it to cool down.

9. Check:

• Coolant level

Refer to “CHECKING THE COOLANT LEV-
EL” on page 3-8.

EASB296075

CHECKING THE RADIATOR CAP

1. Check:

• Seal (radiator cap) “1”

• Valve and valve seat “2”

Crack/damage



Replace.

Exist fur deposits



Clean or replace.

EASB296076

CHECKING THE RADIATOR CAP VALVE
OPENING PRESSURE

1. Check:

• Radiator cap valve opening pressure

▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼

a. Install the radiator cap tester adapter “2” and

the radiator cap tester “3” to the radiator cap
“1,” and activate the tester to check whether
it can stay for 5 to 10 seconds within stan-
dard pressure values.

TIP

Before attaching the cap to the tester, apply
water to its sealing surface.

No stay



Replace.

▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲

Coolant drain bolt

10 Nm (1.0 m·kgf, 7.2 ft·lbf)

Recommended coolant

High quality ethylene glycol

anti-freeze containing anti-cor-

rosion for aluminum engine

Radiator (including all routes)

1.00 L (1.06 US qt, 0.88 Imp.qt)

Coolant mixing ratio

1:1 (Coolant:Water)

New

T

R

.

.

Radiator cap valve opening pres-

sure

107.9–137.3 kPa (1.08–1.37 kg/

cm

2

,15.6–19.9 psi)

Radiator cap tester

90890-01325

Mityvac cooling system tester kit

YU-24460-A

Radiator cap tester adapter

90890-01352

Pressure tester adapter

YU-33984

«
...
95
96
97
98
99
...
»

Содержание YZ 2016 Series









































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для YZ 2016 Series

750 Sport Bevel Heaven

Бренд: Ducati Страницы: 235

Бренд: Yamaha Страницы: 124

Бренд: Honda Страницы: 102

GM STAR 250 1986

Бренд: Maico Страницы: 32

Бренд: hepco & becker Страницы: 5

Бренд: Yamaha Страницы: 287

Бренд: Yamaha Страницы: 109

Бренд: Yamaha Страницы: 122

Бренд: Yamaha Страницы: 142

Бренд: Yamaha Страницы: 118

Бренд: DYNATEK Страницы: 4

Бренд: tucanourbano Страницы: 4

Sport 1 180 - 487.3

Бренд: CZ Страницы: 42

Бренд: Beta Страницы: 214

Бренд: Beta Страницы: 243

Бренд: Rothewald Страницы: 19

450 EXC RACING 2006

Бренд: KTM Страницы: 111

Бренд: KED Страницы: 52

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды