Yamaha YZ 2016 Series Скачать руководство пользователя страница 324 | Manualshive

Страница: 324 / 392

background image

FUEL INJECTION SYSTEM

8-22

EASB296341

YAMAHA DIAGNOSTIC TOOL

This model uses the Yamaha diagnostic tool to identify malfunctions.
For information about using the Yamaha diagnostic tool, refer to the operation manual that is included
with the tool.

FEATURES OF THE YAMAHA DIAGNOSTIC TOOL

A diagnosis can be made more quickly than traditional methods with the Yamaha diagnostic tool.
Using this software, ECU and sensor data, as well as fault diagnosis, vehicle maintenance, and any
necessary information can be recorded and displayed on your computer screen through a USB
adapter connected to the computer interface with a communication cable connected to the vehicle’s
ECU.
Data obtained in various functions can be saved as vehicle history, and can be accumulated.

FUNCTIONS OF THE YAMAHA DIAGNOSTIC TOOL

However, the diagnostic tool cannot be used to freely change the basic vehicle functions, such as
adjusting the ignition timing.

CONNECTING THE YAMAHA DIAGNOSTIC TOOL

1. Remove the coupler for connecting setting tool.

Yamaha diagnostic tool

90890-03231

Yamaha diagnostic tool (US)

90890-03234

Fault diagnosis mode

Fault codes recorded on the ECU are read, and the con-

tents are displayed.

Function diagnostic mode

Check the operation of the output value of each sensor

and actuator.

Inspection mode

Determine whether each sensor or actuator is functioning

properly.

CO adjustment mode

Adjust the concentration of CO admissions during idling.

Monitoring mode

Displays a graph of sensor output values for actual oper-

ating conditions.

Logging mode

Records and saves the sensor output value in actual driv-

ing conditions.

View log

Displays the logging data.

ECU rewrite

If necessary, the ECU is rewritten using the ECU rewrite

data provided by Yamaha. Ignition timing adjustment, etc.

cannot be changed from the vehicle’s original state.

«
...
322
323
324
325
326
...
»

Содержание YZ 2016 Series









































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для YZ 2016 Series

SIDE FORCE 445cc

Бренд: Mash Страницы: 27

Бренд: Suzuki Страницы: 59

Бренд: Kask Страницы: 68

Бренд: OKBABY Страницы: 35

Бренд: Zero Страницы: 290

Бренд: hepco & becker Страницы: 3

Бренд: Shark Страницы: 44

Бренд: Husqvarna Страницы: 107

Бренд: Husqvarna Страницы: 280

Бренд: Husqvarna Страницы: 162

Бренд: Husqvarna Страницы: 321

Бренд: Husqvarna Страницы: 364

2004 DUAL PURPOSE SM 610

Бренд: Husqvarna Страницы: 188

Бренд: Husqvarna Страницы: 269

Бренд: Husqvarna Страницы: 322

Бренд: Husqvarna Страницы: 308

Бренд: Husqvarna Страницы: 169

Бренд: Husqvarna Страницы: 320

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды