Yamaha YZ 2016 Series Скачать руководство пользователя страница 367

Страница: 367 / 392

ELECTRICAL COMPONENTS

8-65

b. Measure the stator coil resistance.

▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲

EASB296359

CHECKING THE RECTIFIER/REGULATOR

1. Check:

• Charging voltage

Out of specification



Replace the rectifier/

regulator.

▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼

a. Set the digital tachometer to the ignition coil.

b. Connect the pocket tester (DC 20 V) to the

rectifier/regulator coupler as shown.

c. Start the engine and let it run at approxi-

mately 5000 r/min.

d. Measure the charging voltage.

▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲

EASB296360

CHECKING THE RADIATOR FAN MOTOR
(For JPN)

1. Check:

• Radiator fan motor

Faulty/rough movement



Replace.

▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼

a. Disconnect the radiator fan motor coupler

from the wire harness.

b. Connect the battery (DC 12 V) as shown.

c. Measure the radiator fan motor movement.

▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲

EASB296361

CHECKING THE COOLANT TEMPERATURE
SENSOR

1. Remove:

• Coolant temperature sensor

EWA

WARNING

• Handle the coolant temperature sensor

with special care.

• Never subject the coolant temperature

sensor to strong shocks. If the coolant
temperature sensor is dropped, replace it.

• Positive tester probe



White “2”

• Negative tester probe



White “3”

No load regulated voltage

14.1–14.9 V

Digital tachometer

90890-06760

Digital tachometer

YU-39951-B

Pocket tester

90890-03112

Analog pocket tester

YU-03112-C

• Positive tester probe



Red “1”

• Negative tester probe



Black “2”

• Positive battery terminal



Blue “1”

• Negative battery terminal



Black “2”

12V

Содержание YZ 2016 Series









































































































































































































































































































































































































Результаты поиска

Содержание YZ 2016 Series

Отзывы:

Похожие инструкции для YZ 2016 Series

Бренды по названию

Популярные бренды

Yamaha YZ 2016 Series, Руководство по эксплуатации для владельца

Результаты поиска

Содержание YZ 2016 Series

Отзывы:

Похожие инструкции для YZ 2016 Series

Бренды по названию

Популярные бренды