Yamaha YZ 2016 Series Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 392

background image

MAINTENANCE AFTER BREAK-IN

1-23

EASB296048

MAINTENANCE AFTER BREAK-IN

After a break-in, perform careful maintenance
to get ready for the next practice or race.
Refer to “PRE-OPERATION INSPECTION
AND MAINTENANCE” on page 3-7.

EASB296049

MAJOR MAINTENANCE

1. For the engine

• Leaks around the engine

Check for pressure leaks from the cylinder
head or the cylinder, oil leaks from the
crankcase or the case cover, leaks from the
coolant system, and other leaks.

• Check that the valve, the cylinder head, the

cylinder, the piston, and the piston ring fit
one another, and that contact between the
valve and the cylinder head, and that be-
tween the cylinder and the piston are cor-
rect.

• Engine oil change

Drain the oil, and check for dirt and foreign
materials such as metal chips. (If any foreign
material is mixed, disassemble and check
the crankcase.)
Pour the specified amount of the recom-
mended oil.

• AC magneto

Check for looseness in mounted areas of
the rotor and the stator.
Check that the connector is not being dis-
connected.

• Silencer

Check the main body and stay for cracks.
Check for leaks.

• Mounting bolts and nuts

Check for looseness in mounted areas of
parts, as well as engine mounting bolts and
engine brackets.

2. For the chassis

• Check welds and mounted areas of the

frame, the swingarm, the link, the bracket,
and so on, for looseness and cracks.

• Wheel (s)

Check the wheel for runout. Check the
spoke for looseness.

• Brake(s)

Check the brake disc mounting bolt for
looseness.
Check that the reservoir contains the speci-
fied amount of brake fluid. Check for leaks.

• Cable

Grease and adjust cables.

• Drive chain

Lubricate the drive chain and adjust its ten-
sion.

• Fuel tank

Clean the inside of the fuel tank. Check for
leaks.

• Suspension

Check for oil leaks in the front fork or the rear
shock absorber. Check that the mounted
conditions are good.

• Sprocket

Check for looseness in the sprocket mount-
ed on the rear wheel.

• Mounting bolts and nuts

Check mounted areas for looseness.

ECA

NOTICE

After a break-in or before each race, always
check the points shown in “TORQUE-
CHECK POINTS” for tightening torques and
retighten them. (Refer to “TORQUE-CHECK
POINTS” on page 1-24.)

• Greasing and oiling

Always grease or oil the specified points.

«
...
33
34
35
36
37
...
»

Содержание YZ 2016 Series









































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для YZ 2016 Series

Бренд: R&G Страницы: 14

Бренд: R&G Страницы: 6

Бренд: Nolan Страницы: 24

Бренд: hepco & becker Страницы: 3

Бренд: Blata Страницы: 17

Бренд: MRA Страницы: 6

MOTO NOSTRA MN4602

Бренд: SC Страницы: 8

Бренд: Yamaha Страницы: 80

Бренд: Yamaha Страницы: 86

Бренд: Yamaha Страницы: 90

Бренд: Yamaha Страницы: 88

Бренд: Yamaha Страницы: 92

Бренд: Yamaha Страницы: 388

Бренд: Yamaha Страницы: 18

R 1200 R Classic

Бренд: BMW Страницы: 1

Бренд: Shad Страницы: 12

Бренд: Montesa Страницы: 114

4Ride MST260 2016

Бренд: Montesa Страницы: 158

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды