Yamaha YZ 2016 Series Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 392

background image

INCLUDED PARTS

1-4

EASB296014

INCLUDED PARTS

EASB296015

SPARK PLUG WRENCH

The spark plug wrench “1” is used to remove or
install the spark plug.

EASB296016

NIPPLE WRENCH

The nipple wrench “1” is used to tighten the
spoke.

EASB296017

HANDLEBAR PROTECTOR

Install the handlebar protector “1” with the mark
“a” facing forward.

EASB296018

FUEL HOSE JOINT COVER

The fuel hose joint covers “1” are used to pre-
vent mud, dust, and other foreign materials
from entering the inside when the fuel hose is
disconnected.

EASB296019

COUPLER FOR CONNECTING OPTIONAL
PART

The coupler “1” is used for connecting the op-
tional Power Tuner and so on.

ECA

NOTICE

When no optional parts, etc. are connected,
connect the connection terminal to the orig-
inal coupler.
Before disconnecting the coupler, thor-
oughly wipe off any mud or water stuck to it.

The Power Tuner is an optional part.

1

1

a

1

A

A

Part name

Part number

GYTR Power Tuner

(For USA)

33D-H59C0-V2

YZ Power Tuner

(Except for USA)

33D-859C0-11

1

1

«
...
14
15
16
17
18
...
»

Содержание YZ 2016 Series









































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для YZ 2016 Series

Бренд: WangYe Страницы: 19

Бренд: Nolan Страницы: 80

Бренд: Touratech Страницы: 4

Бренд: Vance and hines Страницы: 5

Бренд: Parkside Страницы: 24

Бренд: Parkside Страницы: 109

Бренд: URAL Motorcycles Страницы: 104

ACCESORIES 2005

Бренд: Triumph Страницы: 6

Clothing Range 2006

Бренд: Triumph Страницы: 19

2007 ROCKET III

Бренд: Triumph Страницы: 20

Бренд: Triumph Страницы: 136

Speed Triple 1200 RS

Бренд: Triumph Страницы: 184

Scrambler 1200 XC

Бренд: Triumph Страницы: 640

Бренд: Montesa Страницы: 114

4Ride MST260 2016

Бренд: Montesa Страницы: 158

Бренд: Kinroad Страницы: 26

Elefant 650 USA

Бренд: Cagiva Страницы: 136

Бренд: Baotian Страницы: 121

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды