Yamaha YZ 2016 Series Скачать руководство пользователя страница 161

Страница: 161 / 392

HANDLEBAR

4-33

EASB296168

REMOVING THE HANDLEBAR

1. Stand the vehicle on a level surface.

EWA

WARNING

Securely support the vehicle so that there is
no danger of it falling over.

2. Remove:

• Clutch switch “1”

TIP

Press the projection, and remove it from the
clutch lever assembly.
3. Remove:

• Handlebar grip “1”

TIP

Blow compressed air between the left handle-
bar and the handlebar grip, and gradually push
the grip off the handlebar.

4. Remove:

• Throttle cable housings “1”
• Throttle grip “2”

TIP

While removing the throttle cable housing, pull
back the rubber cover “3”.

EASB296169

CHECKING THE HANDLEBAR

1. Check:

• Handlebar

Bends/cracks/damage



Replace.

EWA

WARNING

Do not attempt to straighten a bent handle-
bar as this may dangerously weaken it.

EASB296170

INSTALLING THE HANDLEBAR

1. Stand the vehicle upright on a level surface.

EWA

WARNING

Securely support the vehicle so that there is
no danger of it falling over.

2. Install:

• Damper “1”
• Lower handlebar holders“2” (temporarily)
• Handlebar “3”
• Upper handlebar holders “4”

TIP

• Install the lower handlebar holders with them

side having the greater distance “a” from the
mounting bolt center facing forward.

• Installing the lower handlebar holders in the

reverse direction allow the front-to-rear offset
amount of the handlebar position to be
changed.

• The upper handlebar holders should be in-

stalled with the punch marks “b” facing for-
ward.

• When installing the handlebar, make sure that

right and left marks “c” are in place identically
on both sides.

• Install the handlebar so that the projection “d”

of the upper handlebar holders is positioned
at the mark on the handlebar as shown.

ECA

Upper handlebar holder bolt

28 Nm (2.8 m·kgf, 20 ft·lbf)

Содержание YZ 2016 Series









































































































































































































































































































































































































Результаты поиска

Содержание YZ 2016 Series

Отзывы:

Похожие инструкции для YZ 2016 Series

Бренды по названию

Популярные бренды

Yamaha YZ 2016 Series, Руководство по эксплуатации для владельца

Результаты поиска

Содержание YZ 2016 Series

Отзывы:

Похожие инструкции для YZ 2016 Series

Бренды по названию

Популярные бренды