Yamaha YZ 2016 Series Скачать руководство пользователя страница 251

Страница: 251 / 392

KICKSTATER

5-52

3. Install:

• Spring guide “1”

TIP

Slide the spring guide into the kick shaft, make
sure the groove “a” in the spring guide fits on
the stopper of the torsion spring.

4. Install:

• Kick shaft assembly “1”

TIP

• Before installation, apply molybdenum disul-

fide grease to the contacting surfaces of the
kick shaft ratchet wheel guide “2” and the kick
shaft stopper “a”.

• Apply the engine oil on the kick shaft.
• Slide the kick shaft assembly into the crank-

case and make sure the kick shaft stopper “a”
fits into the kick shaft ratchet wheel guide.

5. Install:

• Torsion spring “1”

TIP

Turn the torsion spring clockwise and hook into
the proper hole “a” in the crankcase.

EASB296260

INSTALLING THE KICK IDLE GEAR

1. Install:

• Kick idle gear “1”
• Washer “2”
• Circlip “3”

TIP

• Apply the engine oil on the kick idle gear inner

circumference.

• Install the kick idle gear with its depressed

side “a” toward you.

New

Содержание YZ 2016 Series









































































































































































































































































































































































































Результаты поиска

Содержание YZ 2016 Series

Отзывы:

Похожие инструкции для YZ 2016 Series

Бренды по названию

Популярные бренды

Yamaha YZ 2016 Series, Руководство по эксплуатации для владельца

Результаты поиска

Содержание YZ 2016 Series

Отзывы:

Похожие инструкции для YZ 2016 Series

Бренды по названию

Популярные бренды