Yamaha YZ 2016 Series Скачать руководство пользователя страница 107

Страница: 107 / 392

ENGINE

3-19

d. Select an adjusting pad with a proper valve

clearance from the adjusting pad selection
table.

TIP

• There are 25 types of adjusting pads, ranging

from 1.20 mm (0.0472 in) to 2.40 mm (0.0945
in), in increments of 0.05 mm (0.0020 in).

• The field where the number on the originally

installed adjusting pad and the measured
valve clearance intersect shows the adjusting
pad number to replace.

Example:

Pad number = 148
Rounded value = 150

e. Install the new adjusting pads “4” and the

valve lifters “5”.

ECA

NOTICE

Do not twist adjusting pads and valve lifters
forcibly during installation.

TIP

• Apply the engine oil on the valve lifters.
• Apply molybdenum disulfide oil to the valve

stem ends.

• Check that the valve lifters turn smoothly

when rotated with your finger.

• Make sure that valve lifters and adjusting

pads are installed in place.

• Make sure that adjusting pads are installed

with their numbers facing upward.

f. Install the camshafts (exhaust and intake).

Refer to “CAMSHAFT” on page 5-12.

g. Measure the valve clearance again.
h. If the valve clearance is out of specification,

repeat adjusting the valve clearance until it
is within specification.

▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲

Last digit of pad

number

Rounded valve

0, 1 or 2

4, 5 or 6

8 or 9

Содержание YZ 2016 Series









































































































































































































































































































































































































Результаты поиска

Содержание YZ 2016 Series

Отзывы:

Похожие инструкции для YZ 2016 Series

Бренды по названию

Популярные бренды

Yamaha YZ 2016 Series, Руководство по эксплуатации для владельца

Результаты поиска

Содержание YZ 2016 Series

Отзывы:

Похожие инструкции для YZ 2016 Series

Бренды по названию

Популярные бренды