Yamaha YZ 2016 Series Скачать руководство пользователя страница 186 | Manualshive

Страница: 186 / 392

background image

REAR SHOCK ABSORBER ASSEMBLY

4-58

EASB296182

HANDLING THE REAR SHOCK ABSORBER

EWA

WARNING

This rear shock absorber contains highly
compressed nitrogen gas. Before handling
the rear shock absorber, read and make
sure that you understand the following in-
formation. The manufacturer cannot be held
responsible for property damage or person-
al injury that may result from improper han-
dling of the rear shock absorber.
• Do not tamper or attempt to open the rear

shock absorber.

• Do not subject the rear shock absorber to

an open flame or any other source of high
heat. High heat can cause an explosion
due to excessive gas pressure.

• Do not deform or damage the rear shock

absorber in any way. Rear shock absorber
damage will result in poor damping perfor-
mance.

TIP

A break-in is required up to about 50 km of run-
ning.

EASB296183

DISPOSING OF A REAR SHOCK ABSORB-
ER

Before disposing the rear shock absorber, be
sure to extract the nitrogen gas from valve “1”.

EWA

WARNING

• Wear protective glasses to prevent your

eyes from damage due to possible gas or
metal chips scattered.

• To dispose of a damaged or a worn-out

rear shock absorber, take the unit to your
Yamaha dealer for this disposal proce-
dure.

EASB296184

REMOVING THE REAR SHOCK ABSORBER
ASSEMBLY

1. Use a suitable stand to raise the rear wheel

off the ground.

EWA

WARNING

Securely support the vehicle so that there is
no danger of it falling over.

2. Remove:

• Rear shock absorber assembly lower bolt

“1”

TIP

While removing the rear shock absorber as-
sembly lower bolt, hold the swingarm so that it
does not drop down.

3. Remove:

• Rear shock absorber assembly upper bolt
• Rear shock absorber assembly

EASB296185

REMOVING THE BEARING

1. Remove:

• Stopper ring (upper bearing) “1”

TIP

Press in the bearing while pressing its outer
race and remove the stopper ring.

1

1

«
...
184
185
186
187
188
...
»

Содержание YZ 2016 Series









































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для YZ 2016 Series

Бренд: Bajaj Auto Страницы: 38

Pulsar 150 DTS-i

Бренд: Bajaj Страницы: 33

Бренд: Baja motorsports Страницы: 37

Dominar 250 BS VI

Бренд: Bajaj Страницы: 52

Бренд: Baja motorsports Страницы: 4

Бренд: Bajaj Auto Страницы: 40

Бренд: Yamaha Страницы: 650

SIDE FORCE 445cc

Бренд: Mash Страницы: 27

MCL-4000 Series

Бренд: Dakota Digital Страницы: 3

Light Bee QL3000DY

Бренд: Surron Страницы: 18

Бренд: hepco & becker Страницы: 4

Бренд: Shark Страницы: 76

Бренд: hepco & becker Страницы: 4

Бренд: hepco & becker Страницы: 4

Бренд: hepco & becker Страницы: 7

Бренд: hepco & becker Страницы: 2

Бренд: hepco & becker Страницы: 4

Бренд: hepco & becker Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды