Yamaha YZ 2016 Series Скачать руководство пользователя страница 376

Страница: 376 / 392

LIST OF SELF-DIAGNOSTIC AND FAIL-SAFE ACTIONS

9-5

SENSOR OPERATION TABLE

Diag-

nostic

code

No.

Item

Display

Procedure

Throttle position sensor sig-

nal

• Fully closed position

• Fully opened position

• 11–14

• 109–116

• Check with throttle valve

fully closed.

• Check with throttle valve

fully open.

Intake air pressure

Displays the intake air pres-

sure.

Operate the throttle while

pushing the start switch. (If

the display value changes,

the performance is OK.)

Intake air temperature

Displays the intake air tem-

perature.

Compare the actually mea-

sured intake air tempera-

ture with the Yamaha

diagnostic tool display val-

ue.

Coolant temperature

When engine is cold: Dis-

plays temperature closer to

air temperature.

When engine is hot: Displays

current coolant temperature.

Compare the actually mea-

sured coolant temperature

with the Yamaha diagnostic

tool display value.

Lean angle sensor

• Upright

• Overturned

Displays the output voltage.

• 0.4–1.4

• 3.7–4.4

Remove the lean angle

sensor, and incline it more

than 45 degrees.

Monitor voltage

Displays the fuel system volt-

age.

• Approximately 12.0 (V)

—

Neutral switch

• Gear in neutral

• Gear not in neutral

• ON

• OFF

Operate the shift pedal.

EEPROM fault code display

• No fault

• CO adjustment value

• Setting tool adjustment

values 0–8 for fuel injec-

tion amount or ignition tim-

ing

• 00

• 01

• 07

—

Malfunction history ( )

code No. display *1

• There is no history.

• There is some history.

• 00

• Other: Displays the fault

code of ( ).

—

Malfunction history ( )

code No. erasure *1

• There is no history.

• There is some history.

• 00

• Other: Displays the total

number of ( ) and ( ).

Replace all ( ) with ( )

by the operation start pro-

cessing.

Содержание YZ 2016 Series









































































































































































































































































































































































































Результаты поиска

Содержание YZ 2016 Series

Отзывы:

Похожие инструкции для YZ 2016 Series

Бренды по названию

Популярные бренды

Yamaha YZ 2016 Series, Руководство по эксплуатации для владельца

Результаты поиска

Содержание YZ 2016 Series

Отзывы:

Похожие инструкции для YZ 2016 Series

Бренды по названию

Популярные бренды