background image

 

MAN#650508B 

 

 

MVX-8X00 gauge kit 

Gauge kit for 1996-2003 Models 

 

Thank you for purchasing the Dakota Digital MVX gauge kit for your Harley Davidson Touring bike.  This kit is designed to 
be a direct plug in replacement for all touring models from 1996 

– 2003. The kit includes the following gauges and 

features: 
 

 
 
 
Speed

 - programmable speed calibration, performance menu, two trip meters, odometer, count down service miles, hours 

running, miles to empty, security and check engine indicators 

Tachometer

 

– programmable tach, clock, gear position, cruise control indicator, ABS indicator, and high RPM recall 

Oil Pressure

 

– programmable warning point, uses stock sensor or Dakota Digital sensor for higher pressure 

Oil Temperature

 

– programmable warning point, complete with new sensor 

Volts

 

– programmable warning point 

Fuel Level

 

– low fuel warning, uses factory sensor  

Air Temperature

 

– uses factory sensor 

 

 

 
INSTALLATION 

Remove the outer fairing and factory gauges; this will vary by model, please follow the service manual to expose the wiring 
and gauges.  Don’t be alarmed by the amount of wires behind the fairing, this is a direct plug in kit and these detailed 
instructions will guide you through it. 
 
                               
 
 
 
 
 
 
 
 
 
 
 
 
 
    Pic of Street Glide with outer fairing removed                                       Pic of Road Glide with outer fairing removed   

 

REMOVAL OF FACTORY GAUGES

 

Now you are ready to start unplugging and removing the gauges.  Start with the speedometer and tachometer gauge plugs 
and speedometer cable if you are working on a cable drive bike (1996-1999). 

 

IMPORTANT NOTE!

  

This gauge has an odometer preset option that is only available for the first 

100 miles (160km) of operation

. See “preset odometer” for instructions. Take note of mileage if you wish to 

transfer mileage over to new gauges. 

Содержание MVX-8X00















Отзывы: