background image

Transport and storage

Delivery check

Check delivered items immediately after arrival for

transport damage and completeness. In case of any

damage or an incomplete shipment, contact the ship-

ping company and your supplier immediately.

Fire damper

Attachments/accessories, if any

Operating manual (1 per shipment)

 Colour hues on the damper blade

The blades of fire dampers are treated with a

greenish impregnating agent. Resulting colour hues

on the damper blade are due to technical reasons

and do not constitute a defect of any kind.

Transport on site

If possible, take the fire damper in its transport pack-

aging up to the installation location.

Storage

If the unit has to be stored temporarily:

Remove any plastic wrapping.

Protect the unit from dust and contamination.

Store the unit in a dry place and away from direct

sunlight.

Do not expose the unit to the effects of weather (not

even in its packaging).

Do not store the unit below -40 °C or above 50 °C.

Packaging

Properly dispose of packaging material.

Transport and storage

 

 

Fire damper Type FKRS-EU

14

Содержание FKRS-EU

















































































































































































Отзывы: