actionair Smoke/Shield PTC Скачать руководство пользователя | Manualshive

Страница: 1 / 8

background image

August 2004

PTC Dampers

Actionair

Installation and Operating Instructions

Smoke/Shield PTC, Vent/Shield PTC,
Hot/Shield PTC, Smoke/Shield PTC, and
Hot/Shield Vent PTC are all trademarks
of Actionair.

Smoke/Shield PTC
Modes 5 and 6 shown.

Hot/Shield PTC
Modes 5 and 6 shown.

Index

Heath and Safety.
General Information.
PTC Damper Installation.

2

Smoke/Shield PTC
Mode 1 Installation.

3

Smoke/Shield PTC and
Vent/Shield PTC
Modes 5 and 6 Installation.

3

Smoke/Shield PTC and
Vent/Shield PTC Control
Modes Dimensional Data.

4

Smoke/Shield PTC and
Vent/Shield PTC
Application and Wiring.

5

Hot/Shield PTC and
Hot/Shield Vent PTC
Damper Installation and
Dimensional Data.
Application and Wiring.

6

Hot/Shield PTC and
Hot/Shield Vent PTC
Dimensional Data.

7

Hot/Shield PTC and
Hot/Shield Vent PTC
Multiple Assembles

7

Smoke/Shield PTC,
Vent/Shield PTC,
Hot/Shield PTC and
Hot/Shield Vent PTC
Troubleshooting.

8

(Smoke/Shield PTC™ Modes 1,5 & 6
fail-safe spring close with manual or
electrical reset).

(Vent/Shield PTC™ Modes 5 & 6 fail-
safe spring open with manual or
electrical reset).

(Hot/Shield PTC™ Modes 5 & 6 are
operational up to 300 °C for 1 hour
with fail-safe spring closure).

(Hot/Shield Vent PTC™ are
operational up to 300 °C for 1 hour
with fail-safe spring opening).

Smoke/Shield PTC, Vent/Shield PTC,

Hot/Shield PTC, and Hot/Shield Vent PTC

1
2
3
...
»

Содержание Smoke/Shield PTC









Отзывы:

Нет отзывов

Похожие инструкции для Smoke/Shield PTC

Бренд: VENCO Страницы: 4

Бренд: KNF Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды