Terex Genie GS-2669 BE Скачать руководство пользователя страница 45

Страница: 45 / 205

May 2015

Service Manual

Checklist B Procedures

Part No. 1257106

GS-2669 BE • GS-3369 BE • GS-4069 BE

B-3

Inspect the Tires, Wheels and

Castle Nut Torque

Genie specifications require that this procedure be

performed every 250 hours or quarterly, whichever

comes first.
Maintaining the tires and wheels, including proper

wheel fastener torque, is essential to safe

operation and good performance. Tire and/or

wheel failure could result in a machine tip-over.

Component damage may also result if problems

are not discovered and repaired in a timely fashion.

Bodily injury hazard. An

over-inflated tire can explode

and could cause death or serious

injury.

Tip-over hazard. Do not use

temporary flat tire repair

products.

Note: The tires on some machines are foam-filled

and do not need air added to them.

1 Check tire surface and sidewalls for cuts,

cracks, punctures and unusual wear.

2 Check each wheel for damage, bends and

cracks.

3 Remove the castle nut cotter pin and check

each castle nut for proper torque. Refer to

Maintenance Procedure,

Grease the Steer

Axle and Wheel Bearings

Note: Always replace the cotter pin with a new one

when removing the castle nut or when checking the

torque of the castle nut.

4 Check each lug nut for proper torque. Refer to

Specifications,

Machine

Specifications

5 Check the pressure in each air-filled tire.

B-4

Perform Engine Maintenance

Genie requires that this procedure be performed

every 250 hours or quarterly, whichever comes

first.

1 Perform the following maintenance

procedures:

•

Replace engine oil

•

Replace oil filter

Required maintenance procedures and additional

engine information is available in the

Kohler KD350

Operator's Manual

(Kohler part number

ED0053028360).

Kohler KD350 Operator's Manual

Genie part number

1255885

Содержание Genie GS-2669 BE














































































































































































































Результаты поиска

Содержание Genie GS-2669 BE

Отзывы:

Похожие инструкции для Genie GS-2669 BE

Бренды по названию

Популярные бренды

Terex Genie GS-2669 BE, Руководство по обслуживанию

Результаты поиска

Содержание Genie GS-2669 BE

Отзывы:

Похожие инструкции для Genie GS-2669 BE

Бренды по названию

Популярные бренды