Terex Genie GS-2669 BE Скачать руководство пользователя страница 127

Страница: 127 / 205

May 2015

Service Manual

Non-steer Axle Components

Part No. 1257106

GS-2669 BE • GS-3369 BE • GS-4069 BE

111

11 Using a suitable supporting device, secure the

rear axle assembly. Do not apply pressure.

1  axle pivot pin
2  retaining fasteners
3  axle assembly

12 Remove the axle pivot pin retaining fasteners.
13 Using a soft metal drift, remove the axle pivot

pin. Remove the axle assembly from the

machine.

1  axle assembly
2  drive hub
3  retaining fasteners (x4)
4  drive motor

14 Remove the retaining fasteners that secure

the drive motor to the drive hub.

15 Support and slide the drive motor shaft out of

the drive hub. Remove the drive motor from

the machine.

Содержание Genie GS-2669 BE














































































































































































































Результаты поиска

Содержание Genie GS-2669 BE

Отзывы:

Похожие инструкции для Genie GS-2669 BE

Бренды по названию

Популярные бренды

Terex Genie GS-2669 BE, Руководство по обслуживанию

Результаты поиска

Содержание Genie GS-2669 BE

Отзывы:

Похожие инструкции для Genie GS-2669 BE

Бренды по названию

Популярные бренды