Terex Genie GS-2669 BE Скачать руководство пользователя страница 161

Страница: 161 / 205

May 2015

Service Manual

Fault Codes

Part No. 1257106

GS-2669 BE • GS-3369 BE • GS-4069 BE

145

Type "CXXX" Faults

DTC

Number

Message on

GCON LCD

Description

Possible Causes

Failure Mode

C001

C001:GCON ECM

FAULT TYPE 1

GCON ECM CRC check error.

• Incorrect software file.

• GCON ECM internal failure.

All functions inhibited.

C004

C004:GCON ECM

FAULT TYPE 4

GCON ECM master switch error.

• Short circuit in the master switch circuit.

• GCON ECM.

All functions inhibited.

C005

C005:GCON ECM

FAULT TYPE 5

GCON ECM safety switch error.

• Short circuit in the safety switch circuit.

• GCON ECM.

All functions inhibited.

C006

C006:GCON ECM

FAULT TYPE 6

GCON input redundancy error.

• Input conditioning circuit failure.

• GCON ECM.

All functions inhibited.

C007

C007:GCON ECM

FAULT TYPE 7

GCON ECM inter-processor.

• Incorrectly programmed device.

• Error in loading software on device.

• GCON ECM.

All functions inhibited.

C009

C009:GCON ECM

FAULT TYPE 9

GCON fault type 9.

• Contact Genie support.

C010

C010:SECONDARY

NOT PROGRAMMED

Secondary not programmed.

• Reinstall software

• Contact Genie support.

All functions inhibited.

C021

C021:PCON NOT

DETECTED

Communication failure between

GCON and PCON.

• CAN communication failure.

• CAN communication harness.

• PCON unplugged.

• GCON or PCON ECM.

All functions inhibited.

C023

C023:MACHINE

MODEL FAULT

Discrepancy between model

detected and model programmed.

• Incorrect machine model programmed.

• GCON or PCON ECM.

All functions inhibited.

C025

C025:SYSTEMFAULT

PLAT OVLD:NOCAL

Platform overload system not

calibrated.

• Platform overload system not calibrated.

• GCON or PCON ECM.

All functions inhibited.

C028

C028:SERVICE

OVERRIDE MODE ON

Machine is in service override mode. • Machine programmed for use in service override mode.

All functions inhibited

except for down function

and up function.
Platform can be elevated

only once with the

maximum elevate time of

XX seconds.
Elevate time XX depends

on machine model.

C029

C029:SYSTEMFAULT

OUTRIGGER:NoCal

Outrigger fault, not calibrated.

• Calibrate outriggers

• Contact Genie support.

All functions operate. Will

not lift above the down

limit switches.

C030

C030:DCON RR ECM

FAULT TYPE 01

Hardware failure of the right rear

drive controller.

• Right rear DCON ECM.

Performance reduced or

all functions inhibited.

C031

C031:DCON LR ECM

FAULT TYPE 01

Hardware failure of the left rear drive

controller.

• Left rear DCON ECM.

Performance reduced or

all functions inhibited.

C032

C032:DCON RR ECM

FAULT TYPE 02

Setup initialization failure of the right

rear drive controller at system

startup.

• Drive input active at system startup.

• Faulty drive joystick.

• Incorrect software.D14

• Right rear DCON ECM.

Performance reduced or

drive inhibited or all

functions inhibited.

C033

C033:DCON LR ECM

FAULT TYPE 02

Setup initialization failure of the left

rear drive controller at system

startup.

• Drive input active at system startup.

• Faulty drive joystick.

• Incorrect software.D14

• Left rear DCON ECM.

Performance reduced or

drive inhibited or all

functions inhibited.

Содержание Genie GS-2669 BE














































































































































































































Результаты поиска

Содержание Genie GS-2669 BE

Отзывы:

Похожие инструкции для Genie GS-2669 BE

Бренды по названию

Популярные бренды

Terex Genie GS-2669 BE, Руководство по обслуживанию

Результаты поиска

Содержание Genie GS-2669 BE

Отзывы:

Похожие инструкции для Genie GS-2669 BE

Бренды по названию

Популярные бренды