Terex Genie GS-2669 BE Скачать руководство пользователя страница 157

Страница: 157 / 205

May 2015

Service Manual

Fault Codes

Part No. 1257106

GS-2669 BE • GS-3369 BE • GS-4069 BE

141

Type "UXXX" Faults, continued

DTC

Number

Message on

GCON LCD

Description

Possible Causes

Failure Mode

U033

U033:JSTICKFAULT

OUT OF CAL RANGE

PCON drive joystick signal is outside

acceptable calibration.

• PCON drive joystick is not in neutral position range at

system startup.

• PCON joystick.

• GCON ECM.

All drive and steer

functions inhibited.

U034

U034:JSTICKFAULT

OUT OF RANGE:HI

Short circuit of the PCON drive

joystick signal to battery positive at

system startup.

• Short circuit of the PCON drive joystick signal circuit.

• PCON joystick.

• GCON ECM.

All drive and steer

functions inhibited.

U035

U035:JSTICKFAULT

OUT OF RANGE:LO

Short circuit of the PCON drive

joystick signal to battery negative at

system startup.

• Short circuit of the PCON drive joystick signal circuit.

• PCON joystick.

• GCON ECM.

All drive and steer

functions inhibited.

U036

U036:SWITCHFAULT

GCON + PCON:ON

Mis-wiring or short circuit of GCON

key switch.

• Short circuit of the GCON key switch harness.

• GCON key switch.

• GCON ECM.

All functions inhibited.

U037

U037:SWITCHFAULT

FOOTSW PRESSED

Foot switch or Enable switch

depressed at startup.

• Enable switch activated at startup.

• Enable switch contact stuck closed.

• PCON ECM.

All drive and steer

functions inhibited.

U038

U038:SWITCHFAULT

FOOTSWITCH:Bat+

Short circuit of the PCON power

circuit to enable switch to battery

positive.

• Short circuit in PCON power harness.

• Enable switch shorted battery positive.

• PCON ECM.

All drive and steer

functions inhibited.

U039

U039:SWITCHFAULT

FOOTSW:Open/Bat-

Open or short circuit of the PCON

power circuit to enable switch to

battery negative.

• Open or short circuit in PCON power harness.

• Enable switch short or open to battery negative.

• PCON ECM.

All drive and steer

functions inhibited.

U042

U042:SWITCHFAULT

PCON DRIVE MODE

PCON drive mode switch stuck

closed, or depressed prior to startup.

• Drive mode switch stuck closed.

• Drive mode switch is depressed at system startup.

• PCON ECM.

Drive function inhibited.

U043

U043:SWITCHFAULT

PCON OR MODE

PCON outrigger mode switch stuck

closed, or depressed prior to startup.

• Outrigger mode switch stuck closed.

• Outrigger mode switch is depressed at system startup.

• PCON ECM.

Outrigger extend / retract

function inhibited.

U045

U045:SWITCHFAULT

PCON DRIVE EN

Short circuit of the PCON drive

enable switch at system startup.

• Short circuit of the PCON drive enable switch.

• PCON ECM.

• GCON ECM.

All drive and steer

functions inhibited.

U046

U046:SWITCHFAULT

PCON LIFT MODE

PCON lift mode fault

• PCON lift mode switch is depressed at system startup.

• PCON ECM.

All functions operate

except platform up or

down.

Содержание Genie GS-2669 BE














































































































































































































Результаты поиска

Содержание Genie GS-2669 BE

Отзывы:

Похожие инструкции для Genie GS-2669 BE

Бренды по названию

Популярные бренды

Terex Genie GS-2669 BE, Руководство по обслуживанию

Результаты поиска

Содержание Genie GS-2669 BE

Отзывы:

Похожие инструкции для Genie GS-2669 BE

Бренды по названию

Популярные бренды