Terex Genie GS-2669 BE Скачать руководство пользователя страница 60

Страница: 60 / 205

Service Manual

May 2015

Checklist E Procedures

GS-2669 BE • GS-3369 BE • GS-4069 BE

Part No. 1257106

5 Check for wheel bearing wear by attempting to

move the wheel hub side to side, then up and

down.

Result:

There is no side to side or up and

down movement. Proceed to step 10.

Result:

There is side to side or up and down

movement Proceed to step 6.

6 Remove the dust cap from the hub. Remove

the cotter pin from the castle nut.

7 Tighten the castle nut to 150 ft-lbs / 203 Nm to

seat the bearings.

8 Fully loosen the castle nut and re-tighten to

35 ft-lbs / 48 Nm.

9 Check for wheel bearing wear by attempting to

move the wheel hub side to side, then up and

down.

Result:

There is no side to side or up and

down movement. Proceed to step 10.

Result:

There is side to side or up and down

movement. Proceed to step 10 and replace

the wheel bearings with new ones.

Note: When replacing a wheel bearing, both the

inner and outer bearings, including the pressed-in

races, must be replaced.

10 Remove the dust cap from the hub. Remove

the cotter pin from the castle nut.

11 Remove the castle nut.
12 Pull the hub off of the spindle. The spindle

washer, thrust washer and outer bearing

should fall loose from the hub.

13 Place the hub on a flat surface and gently pry

the bearing seal out of the hub. Remove the

rear bearing.

14 Pack both bearings with clean, fresh grease.
15 Place the large inner bearing into the rear of

the hub.

16 Install a new bearing grease seal into the hub

by pressing it evenly into the hub until it is

flush.

17 Slide the hub onto the yoke spindle.

Component damage hazard. Do

not apply excessive force or

damage to the lip of the seal may

occur.

18 Place the outer bearing into the hub.
19 Install the spindle washer, thrust washer and

castle nut.

20 Tighten the slotted nut to 150 ft-lbs / 203 Nm

to seat the bearings.

21 Fully loosen the castle nut and re-tighten to

35 ft-lbs / 48 Nm.

22 Install a new cotter pin. Bend the cotter pin to

lock it in place.

Note: Always use a new cotter pin when installing a

castle nut.

23 Install the dust cap.

Содержание Genie GS-2669 BE














































































































































































































Результаты поиска

Содержание Genie GS-2669 BE

Отзывы:

Похожие инструкции для Genie GS-2669 BE

Бренды по названию

Популярные бренды

Terex Genie GS-2669 BE, Руководство по обслуживанию

Результаты поиска

Содержание Genie GS-2669 BE

Отзывы:

Похожие инструкции для Genie GS-2669 BE

Бренды по названию

Популярные бренды