Terex Genie GS-2669 BE Скачать руководство пользователя страница 113

Страница: 113 / 205

May 2015

Service Manual

Manifolds

Part No. 1257106

GS-2669 BE • GS-3369 BE • GS-4069 BE

How to T est a Coil Di ode

How to Test a Coil Diode

Properly functioning coil diodes protect the

electrical circuit by suppressing voltage spikes.

Voltage spikes naturally occur within a function

circuit following the interruption of electrical current

to a coil. Faulty diodes can fail to protect the

electrical system, resulting in a tripped circuit

breaker or component damage.

Electrocution/burn hazard.

Contact with electrically charged

circuits could result in death or

serious injury. Remove all rings,

watches and other jewelry.

1 Test the coil for resistance. Refer to Repair

Procedure,

How to Test a Coil

2 Connect a 10W resistor to the negative

terminal of a known good 9V DC battery.

Connect the other end of the resistor to a

terminal on the coil.

Resistor 10Ω

Genie part number 27287

Note: The battery should read 9V DC or more when

measured across the terminals.

1  multimeter
2  9v DC battery
3  10Ω resistor
4  coil

3 Set a multimeter to read DC current.
Note: The multimeter, when set to read DC current,

should be capable of reading up to 800 mA.

4 Connect the negative lead to the other

terminal on the coil.

5 Momentarily connect the positive lead from

the multimeter to the positive terminal on the

9V DC battery. Note and record the current

reading.

6 At the battery or coil terminals, reverse the

connections. Note and record the current

reading.

Result: Both current readings are greater than

0 mA and are different by a minimum of 20%.

The coil is good.

Result: If one or both of the current readings

are 0 mA, or if the two current readings do not

differ by a minimum of 20%, the coil and/or its

internal diode are faulty and the coil should be

replaced.

Содержание Genie GS-2669 BE














































































































































































































Результаты поиска

Содержание Genie GS-2669 BE

Отзывы:

Похожие инструкции для Genie GS-2669 BE

Бренды по названию

Популярные бренды

Terex Genie GS-2669 BE, Руководство по обслуживанию

Результаты поиска

Содержание Genie GS-2669 BE

Отзывы:

Похожие инструкции для Genie GS-2669 BE

Бренды по названию

Популярные бренды