Terex Genie GS-2669 BE Скачать руководство пользователя страница 33

Страница: 33 / 205

May 2015

Service Manual

Pre-Delivery Preparation Report

Fundamentals

It is the responsibility of the dealer to perform the

Pre-delivery Preparation.
The Pre-delivery Preparation is performed prior to

each delivery. The inspection is designed to

discover if anything is apparently wrong with a

machine before it is put into service.
A damaged or modified machine must never be

used. If damage or any variation from factory

delivered condition is discovered, the machine

must be tagged and removed from service.
Repairs to the machine may only be made by a

qualified service technician, according to the

manufacturer's specifications.
Scheduled maintenance inspections shall be

performed by qualified service technicians,

according to the manufacturer's specifications and

the requirements listed in the responsibilities

manual.

Instructions

Use the operator’s manual on your machine.
The Pre-delivery Preparation consists of

completing the Pre-operation Inspection, the

Maintenance items and the Function Tests.
Use this form to record the results. Place a check in

the appropriate box after each part is completed.

Follow the instructions in the operator’s manual.
If any inspection receives an N, remove the

machine from service, repair and re-inspect it. After

repair, place a check in the R box.

Legend

Y = yes, acceptable

N = no, remove from service

R = repaired

Comments

Pre-delivery Preparation

Pre-operation inspection completed

Maintenance items completed

Function tests completed

Model

Serial number
Date
Machine owner
Inspected by (print)
Inspector signature
Inspector title
Inspector company

Содержание Genie GS-2669 BE














































































































































































































Результаты поиска

Содержание Genie GS-2669 BE

Отзывы:

Похожие инструкции для Genie GS-2669 BE

Бренды по названию

Популярные бренды

Terex Genie GS-2669 BE, Руководство по обслуживанию

Результаты поиска

Содержание Genie GS-2669 BE

Отзывы:

Похожие инструкции для Genie GS-2669 BE

Бренды по названию

Популярные бренды