Terex Genie GS-2669 BE Скачать руководство пользователя страница 65

Страница: 65 / 205

May 2015

Service Manual

Platform Controls

Part No. 1257106

GS-2669 BE • GS-3369 BE • GS-4069 BE

1-2

Joystick

How to Remove the Joystick

1 Push in the red Emergency Stop button to the

off position at both the ground and platform

controls.

2 Disconnect the platform controls from the

control cable at the platform.

3 Remove the fasteners securing the platform

control box to the platform control bracket.

4 Remove the fasteners securing the bottom

cover to the platform control box. Open the

control box.

5 Remove the ties securing the joystick wire

harness.

6 Carefully disconnect the joystick wire harness

from the platform controls circuit board.

Electrocution/burn hazard.

Contact with electrically charged

circuits could result in death or

serious injury. Remove all rings,

watches and other jewelry.

Component damage hazard.

Electrostatic discharge (ESD)

can damage printed circuit board

components. Maintain firm

contact with a metal part of the

machine that is grounded at all

times when handling printed

circuit boards OR use a

grounded wrist strap.

7 Carefully remove the joystick fasteners.
8 Carefully remove the joystick from the platform

control box.

Torque specifications

Joystick fasteners

9 in-lbs

1 Nm

1-3

Platform Controls Alarm

How to Remove the Platform

Controls Alarm

1 Push in the red Emergency Stop button to the

off position at both the ground and platform

controls.

2 Disconnect the platform controls from the

control cable at the platform.

3 Remove the fasteners securing the platform

control box to the platform control bracket.

4 Remove the fasteners securing the bottom

cover to the platform control box. Open the

control box.

5 Disconnect the red and black wires from the

alarm.

Electrocution/burn hazard.

Contact with electrically charged

circuits could result in death or

serious injury. Remove all rings,

watches and other jewelry.

Component damage hazard.

Electrostatic discharge (ESD)

can damage printed circuit board

components. Maintain firm

contact with a metal part of the

machine that is grounded at all

times when handling printed

circuit boards OR use a

grounded wrist strap.

6 Carefully remove the alarm from the platform

control box.

Содержание Genie GS-2669 BE














































































































































































































Результаты поиска

Содержание Genie GS-2669 BE

Отзывы:

Похожие инструкции для Genie GS-2669 BE

Бренды по названию

Популярные бренды

Terex Genie GS-2669 BE, Руководство по обслуживанию

Результаты поиска

Содержание Genie GS-2669 BE

Отзывы:

Похожие инструкции для Genie GS-2669 BE

Бренды по названию

Популярные бренды