Terex Genie GS-2669 BE Скачать руководство пользователя страница 148

Страница: 148 / 205

Service Manual

May 2015

Fault Codes

132

GS-2669 BE • GS-3369 BE • GS-4069 BE

Part No. 1257106

Fault Inspection Procedure

Check the device associated with the faulted circuit

1 Disconnect the faulted device connector.
2 Using a multi-meter, measure resistance between the two

terminals of the faulted device.

3 Resistance should be as follows.

Device

Typical Resistance

Solenoid Valve, Drive

27.2

Ω

Solenoid Valve, Steer

Ω

Solenoid Valve, Platform Up

Ω

Solenoid Valve, Platform Down

6.25

Ω

GCON and PCON Alarm

>1M

Ω

Automotive Horn

1.0

Ω

Contactor Coil

Ω

Go to step 2

No Good

Replace faulted device

Check the harness between the ground controls and the faulted device

1 Disconnect the GCON ECM connectors, C1, C2 and C3.

(or C4 if equipped with outriggers).

2 Disconnect the faulted device connector.
3 Check the continuity between the GCON ECM connector

and the signal side of the faulted device.



Result: Resistance should be close to 0

Ω.

4 Check the continuity between the return side of faulted

device and system ground.



Result: Resistance should be close to 0

Ω.

5 Check resistance between return side and signal side of

the harness plug of faulted device.



Result: Resistance should be 1M

Ω

or higher.

Go to step 3

No Good

Replace or repair harness

Check the GCON ECM

Содержание Genie GS-2669 BE














































































































































































































Результаты поиска

Содержание Genie GS-2669 BE

Отзывы:

Похожие инструкции для Genie GS-2669 BE

Бренды по названию

Популярные бренды

Terex Genie GS-2669 BE, Руководство по обслуживанию

Результаты поиска

Содержание Genie GS-2669 BE

Отзывы:

Похожие инструкции для Genie GS-2669 BE

Бренды по названию

Популярные бренды