Terex Genie GS-2669 BE Скачать руководство пользователя страница 31

Страница: 31 / 205

May 2015

Service Manual

Scheduled Maintenance Procedures

Part No. 1257106

GS-2669 BE • GS-3369 BE • GS-4069 BE

Maintenance Symbols Legend

Note: The following symbols have been used in this

manual to help communicate the intent of the

instructions. When one or more of the symbols

appear at the beginning of a maintenance

procedure, it conveys the meaning below.

Indicates that tools will be required to

perform this procedure.

Indicates that new parts will be required to

perform this procedure.

Indicates that dealer service will be

required to perform this procedure.

Indicates that a cold engine will be

required to perform this procedure.

Indicates that a warm engine will be

required to perform this procedure.

Pre-delivery Preparation Report

The pre-delivery preparation report contains

checklists for each type of scheduled inspection.
Make copies for each inspection. Store completed

forms as required.

Maintenance Schedule

The

Scheduled Maintenance Procedures

section

and the

Maintenance Inspection Report

have been

divided into subsections. Use the following chart to

determine which group(s) of procedures are

required to perform a scheduled inspection.

Inspection

Checklist

Daily or every 8 hours

Quarterly or every 250 hours

A + B

Semi-annually or every 500 hours

A + B + C

Annually or every 1000 hours

A + B + C + D

Two-year or every 2000 hours

A + B + C + D + E

Maintenance Inspection Report

The maintenance inspection report contains

checklists for each type of scheduled inspection.
Make copies of the

Maintenance Inspection Repor

to use for each inspection. Maintain completed

forms for a minimum of 4 years or in compliance

with your employer, jobsite and governmental

regulations and requirements.

Содержание Genie GS-2669 BE














































































































































































































Результаты поиска

Содержание Genie GS-2669 BE

Отзывы:

Похожие инструкции для Genie GS-2669 BE

Бренды по названию

Популярные бренды

Terex Genie GS-2669 BE, Руководство по обслуживанию

Результаты поиска

Содержание Genie GS-2669 BE

Отзывы:

Похожие инструкции для Genie GS-2669 BE

Бренды по названию

Популярные бренды