Terex Genie GS-2669 BE Скачать руководство пользователя страница 89

Страница: 89 / 205

May 2015

Service Manual

Ground Controls

Part No. 1257106

GS-2669 BE • GS-3369 BE • GS-4069 BE

5-3

Auxiliary Platform Lowering

In the event of a main power failure, activating the

auxiliary enable and auxiliary platform lowering

toggle switches at the ground controls will lower the

platform. There is no adjustment required.

1 auxiliary enable toggle switch
2 auxiliary lowering toggle switch

5-4

Level Sensor - Models without

Outriggers

The Electronic Control Module (ECM) is

programmed to deactivate the lift and drive

functions and activate an alarm when a signal is

received from the level sensor.
The tilt alarm sounds when the incline of the

chassis exceeds 2° to the side and 3° to the front or

rear.

How to Install and Calibrate the

Level Sensor

Tip-over hazard. Failure to install

or calibrate the level sensor as

instructed will compromise

machine stability and cause the

machine to tip over, resulting in

death or serious injury. Do not

install or calibrate the level

sensor other than specified in

this procedure.

Note: Perform this procedure with the machine on

a firm, level surface and the platform in the stowed

position. Use a digital level to confirm.

1 Remove the platform controls from the

platform.

Note: If you are not installing a new level

sensor, or you have installed an outrigger level

sensor, proceed to step 7.

Содержание Genie GS-2669 BE














































































































































































































Результаты поиска

Содержание Genie GS-2669 BE

Отзывы:

Похожие инструкции для Genie GS-2669 BE

Бренды по названию

Популярные бренды

Terex Genie GS-2669 BE, Руководство по обслуживанию

Результаты поиска

Содержание Genie GS-2669 BE

Отзывы:

Похожие инструкции для Genie GS-2669 BE

Бренды по названию

Популярные бренды