Terex Genie GS-2669 BE Скачать руководство пользователя страница 120

Страница: 120 / 205

Service Manual

May 2015

Steer Axle Components

104

GS-2669 BE • GS-3369 BE • GS-4069 BE

Part No. 1257106

2 Disconnect the connector with the green/black

wire from the oscillate right coil (item 2) and

swap it with the connector with the blue wire

from the steer right coil (item 3).

1  Green
2  Green/Black
3  Blue
4  Blue/Black

3 Disconnect the connector with the green wire

from the oscillate left coil (item 1) and swap it

with the connector with the blue/black wire

from the steer left coil (item 4).

4 Turn the key switch to platform control and pull

out the red Emergency Stop button to the on

position at both the ground and platform

controls.

5 Slowly drive the machine in a safe direction

and activate steer right.

Result: The right oscillate cylinder will extend

and the left oscillate cylinder will retract.

6 Slowly drive the machine in a safe direction

and activate steer left.

Result: The left oscillate cylinder will extend

and the right oscillate cylinder will retract.

7 Turn the key switch to the off position.
8 Swap the connectors back to the correct coils

using steps 2 an 3 as a reference. Continue to

Check the Steering.

Check the Steering

1 Turn the key switch to platform control and pull

out the red Emergency Stop button to the on

position at both the ground and platform

controls.

2 Activate steer right and verify the machine

steers to the right.

3 Activate steer left and verify the machine

steers to the left.

4 Test the axle oscillate. Refer to Maintenance

Section,

Test the Oscillate Axle

Содержание Genie GS-2669 BE














































































































































































































Результаты поиска

Содержание Genie GS-2669 BE

Отзывы:

Похожие инструкции для Genie GS-2669 BE

Бренды по названию

Популярные бренды

Terex Genie GS-2669 BE, Руководство по обслуживанию

Результаты поиска

Содержание Genie GS-2669 BE

Отзывы:

Похожие инструкции для Genie GS-2669 BE

Бренды по названию

Популярные бренды