Terex Genie GS-2669 BE Скачать руководство пользователя страница 81

Страница: 81 / 205

May 2015

Service Manual

Scissor Components

Part No. 1257106

GS-2669 BE • GS-3369 BE • GS-4069 BE

3-4

Wear Pads

How to Replace the Scissor Arm

Wear Pad

Platform Scissor Arm Slider Blocks:

1 Remove the platform. Refer to Repair

Procedure,

How to Remove the Platform

2 Remove the slider blocks and discard.
3 Install the slider blocks.
Note: When installing the platform the drill holes in

the slider blocks must be on the top and bottom.

4 Install the platform.

Chassis Scissor Arm Wear Pads:

1 Attach a lifting strap from a suitable lifting

device to the ladder at the non-steer end of the

machine. Support the ladder. Do not apply

lifting pressure.

2 Remove the fasteners securing the ladder to

the chassis. Remove the ladder from the

machine and set aside.

Crushing hazard. The ladder

could fall if not properly

supported when the fasteners

are removed from the machine.

3 Using an overhead lifting device attach a strap

to the #1 inner arm at the non-steer end of the

machine.

Note: The overhead lifting device and strap must

be capable of supporting 5000 lbs / 2268 kg.

Crushing hazard. The linkage

assembly could become

unbalanced and fall if not

properly supported.

4 Raise the linkage assembly slightly with the

overhead lifting device just enough to take

pressure off of the slider feet.

Содержание Genie GS-2669 BE














































































































































































































Результаты поиска

Содержание Genie GS-2669 BE

Отзывы:

Похожие инструкции для Genie GS-2669 BE

Бренды по названию

Популярные бренды

Terex Genie GS-2669 BE, Руководство по обслуживанию

Результаты поиска

Содержание Genie GS-2669 BE

Отзывы:

Похожие инструкции для Genie GS-2669 BE

Бренды по названию

Популярные бренды