Terex Genie GS-2669 BE Скачать руководство пользователя страница 162

Страница: 162 / 205

Service Manual

May 2015

Fault Codes

146

GS-2669 BE • GS-3369 BE • GS-4069 BE

Part No. 1257106

Type "CXXX" Faults, continued

DTC

Number

Message on

GCON LCD

Description

Possible Causes

Failure Mode

C034

C034:DCON RR ECM

FAULT TYPE 03

Valve driver failure of the right rear

drive controller.

• Right rear DCON ECM.

Drive functions inhibited.

C035

C034:DCON LR ECM

FAULT TYPE 03

Valve driver failure of the left rear

drive controller.

• Left rear DCON ECM.

Drive functions inhibited.

C036

C036:DCON RR ECM

FAULT TYPE 04

Right rear drive controller voltage

out of range.

• Battery charger connected.

• Batteries to low.

• Right rear DCON ECM.

All functions inhibited.

C037

C037:DCON LR ECM

FAULT TYPE 04

Left rear drive controller voltage out

of range.

• Battery charger connected.

• Batteries to low.

• Left rear DCON ECM.

All functions inhibited.

C038

C038:DCON RR ECM

FAULT TYPE 05

Capacitor charge failure of the right

rear drive controller.

• Open on B+ or B- to the right rear drive controller.

• Right rear DCON ECM.

All functions inhibited.

C039

C039:DCON LR ECM

FAULT TYPE 05

Capacitior charge failure of the left

rear drive controller.

• Open on B+ or B- to the left rear drive controller.

• Left rear DCON ECM.

All functions inhibited.

C040

C040:DCON RR ECM

FAULT TYPE 06

Open circuit to the PEV (B2) circuit

of the right rear drive controller.

• Open circuit of the right rear motor controller harness.

• Key switch relay CR61 not closed.

• Right rear DCON or GCON ECM.

All functions inhibited.

C041

C041:DCON LR ECM

FAULT TYPE 06

Open circuit to the PEV (B2) circuit

of the LEFT rear drive controller.

• Open circuit of the left rear motor controller harness.

• Key switch relay CR61 not closed.

• Left rear DCON or GCON ECM.

All functions inhibited.

C042

C042:DCON RR ECM

FAULT TYPE 07

Open circuit of the key switch circuit

or battery positive/negative of the

right rear drive controller.

• Open circuit of the right rear motor controller harness.

• Open circuit to B+ and/or B-.

• Key switch relay CR61 not closed.

• Right rear DCON or GCON ECM.

All functions inhibited.

C043

C043:DCON LR ECM

FAULT TYPE 07

Open circuit of the key switch circuit

or battery positive/negative of the left

rear drive controller.

• Open circuit of the left rear motor controller harness.

• Open circuit to B+ and/or B-.

• Key switch relay CR61 not closed.

• Left rear DCON or GCON ECM.

All functions inhibited.

C044

C044:DCON RR ECM

FUALT TYPE 08

Communication error of the CAN

circuit between the GCON and the

right rear motor controller.

• Open circuit of the right rear motor controller harness.

• Right rear DCON or GCON ECM.

All functions inhibited.

C045

C045:DCON LR ECM

FAULT TYPE 08

Communication error of the CAN

circuit between the GCON and the

left rear motor controller.

• Open circuit of the left rear motor controller harness.

• Left rear DCON or GCON ECM.

All functions inhibited.

C046

C046:DCON RR ECM

FAULT TYPE 09

Communication error of the CAN

circuit between the GCON and the

right rear motor controller.

• Open or short circuit of the right rear motor controller

harness.

• Right rear DCON or GCON ECM.

All functions inhibited.

C047

C045:DCON LR ECM

FAULT TYPE 09

Communication error of the CAN

circuit between the GCON and the

left rear motor controller.

• Open or short circuit of the left rear motor controller harness.

• Left rear DCON or GCON ECM.

All functions inhibited.

C048

C048:DCON RR ECM

FAULT TYPE 10

Output error of the thermal sensor

circuit of the right rear motor

controller.

• Right rear DCON ECM.

Performance reduced.

C049

C049:DCON LR ECM

FAULT TYPE 10

Output error of the thermal sensor

circuit of the left rear motor

controller.

• Left rear DCON ECM.

Performance reduced.

C050

C050:SOC MONITOR

NOT DETECTED

State of charge monitor not

detected.

• SOC monitor

• SOC monitor harness

• Incorrect baud rate setting on acuity

• GCON ECM.

Performance reduced.

C053

C053:PCON-GCON

SOFTWARE MISMATCH

Software revisions do not match

between the PCON and GCON.

• C053 displayed at GCON, PCON with older software

revision connected to GCON with newer software revision.

• C053 displayed at PCON, PCON with newer software

revision connected to GCON with older software revision.

All functions inhibited.

Содержание Genie GS-2669 BE














































































































































































































Результаты поиска

Содержание Genie GS-2669 BE

Отзывы:

Похожие инструкции для Genie GS-2669 BE

Бренды по названию

Популярные бренды

Terex Genie GS-2669 BE, Руководство по обслуживанию

Результаты поиска

Содержание Genie GS-2669 BE

Отзывы:

Похожие инструкции для Genie GS-2669 BE

Бренды по названию

Популярные бренды