Terex Genie GS-2669 BE Скачать руководство пользователя страница 69

Страница: 69 / 205

May 2015

Service Manual

Platform Components

Part No. 1257106

GS-2669 BE • GS-3369 BE • GS-4069 BE

5 Release the four rail spacers by pulling the

retaining pin and turn them in a downward

position.

1 rail spacer

6 Position a forklift at the steer end of the

machine with the forks even with the bottom of

the platform extension.

7 Carefully slide the platform extension out until

the platform extension makes contact with the

carriage on the forklift.

8 Secure the platform extension deck railings to

the carriage of the forklift to support the

platform extension deck.

9 Carefully slide the platform extension out and

away from the platform and place it on a

structure capable of supporting it.

Crushing hazard. The platform

extension will become

unbalanced and fall when

removed from the machine if not

properly supported and secured

to the forklift.

Содержание Genie GS-2669 BE














































































































































































































Результаты поиска

Содержание Genie GS-2669 BE

Отзывы:

Похожие инструкции для Genie GS-2669 BE

Бренды по названию

Популярные бренды

Terex Genie GS-2669 BE, Руководство по обслуживанию

Результаты поиска

Содержание Genie GS-2669 BE

Отзывы:

Похожие инструкции для Genie GS-2669 BE

Бренды по названию

Популярные бренды